Sponsored Content
Operating Systems Solaris Solaris 10 Changing of nic link_speed Post 302597122 by freshmeat on Thursday 9th of February 2012 08:57:54 AM
Old 02-09-2012
Quote:
Originally Posted by jlliagre
Is e1000g0 connected to the same switch as e1000g1 and e1000g2 ?
yesSmilie:

Last edited by fpmurphy; 02-09-2012 at 10:14 AM..
 

9 More Discussions You Might Find Interesting

1. IP Networking

not able to add nic in solaris 8

Hi Folks, I've just installed solaris 8, but i cannot add my network card. i've reboot the box, got into the configmode, and try'd to add a network card. but it doesn't work. I can't add a ip address to the card, an error occurs. Who do i add it. Kind Regards (3 Replies)
Discussion started by: noripsni
3 Replies

2. UNIX for Advanced & Expert Users

Changing MAC address of a NIC

All, I have a need to software change the MAC address of a NIC in a Sparc Ultra 10 - I believe there is a command that allows to do this at boot up? Is it a missing (to me) part of ifconfig ? If so, what is the syntax? All replies gratefully received ! Thanks Andrew (3 Replies)
Discussion started by: wretch
3 Replies

3. Solaris

NIC drivers+solaris 10

Installed solaris 10 and now i want to connect to internet,to make work this i need to NIC drivers can some body tell me is it possible to get drivers and how to install. I am dying to get rid of this problem..please help me (1 Reply)
Discussion started by: srinivas2828
1 Replies

4. Red Hat

changing ethernet NIC names?

I have an RHEL 5 server with 2 Broadcom on-board NICs and 2 quad-port Intel NICs. After I installed the OS, the Intel NICs became eth0-7, and the onboards are eth8 and eth9. I really need the onboard NICs to be eth0 and eth1 (I have plans to later remove the quad-ports and replace them with 10gE... (1 Reply)
Discussion started by: GKnight
1 Replies

5. Linux

changing speed of NIC Card in linux

Hi, I would like to know how to change the speed of ethernet card in linux? as it is showing auto-neg using mii-tool -v eth0 and my requirement is 100mbps full duplex. Regards, Manoj (3 Replies)
Discussion started by: manoj.solaris
3 Replies

6. Solaris

Solaris, identifying NIC hw issues

Can someone point out which steps are to be done to get information if NIC on Solaris is malfunctioned and/or not working properly. Since my Solaris knowledge is very modest, i would apreciate any help. OS is Solaris 10 x86 Regards. Peasant. ---------- Post updated at 11:57 AM... (0 Replies)
Discussion started by: Peasant
0 Replies

7. Solaris

NIC detection problem in solaris

Hi, Hardware: Mother board: Asus P5G4IC-M LX On board NIC: PCIe Gigabite LAN Kernel Ver.: SunOS 5.10 Generic_141445-09 I've NIC detection problem in Solaris 10. When I was trying to install in x86 machine, it was not asking for any Network settings which means it couldn't find NIC. But... (7 Replies)
Discussion started by: vicky86ind
7 Replies

8. Solaris

x86 Solaris 10 nic driver added but not attached. NIC is not detected.

I couldn't install my nic in solaris 10. I compiled and added the driver but failed to attach the driver and ifconfig output shows only loopback dev. Please see the following output and tell me whether my nic has been detected and why the driver failed to attach? My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies

9. UNIX for Advanced & Expert Users

Changing single path NIC to a teamed connection in same subnet

Dear all, I have a remote CentOS7 server that has two network cards. Each card has four ports and port one of card one was defined with the IP address assigned to the server. So far, so good and it's been working for over a year. We have now got cables sorted out so there are four paths... (4 Replies)
Discussion started by: rbatte1
4 Replies
TPM QUOTE 
TOOLS(8) TPM QUOTE TOOLS(8) NAME
TPM Quote Tools PROGRAMS
tpm_mkuuid, tpm_mkaik, tpm_loadkey, tpm_unloadkey, tpm_getpcrhash, tpm_updatepcrhash, tpm_getquote, tpm_verifyquote DESCRIPTION
TPM Quote Tools is a collection of programs that provide support for TPM based attestation using the TPM quote operation. A TPM contains a set of Platform Configuration Registers (PCRs). In a well configured machine, some of these registers are set to known values during the boot up process or at other times. For example, a PCR might contain the hash of a boot loader in memory before it is run. The TPM quote operation is used to authoritatively verify the contents of a TPM's Platform Configuration Registers (PCRs). During provi- sioning, a composite hash of a selected set of PCRs is computed. The TPM quote operation produces a composite hash that can be compared with the one computed while provisioning. To use the TPM quote operation, keys must be generated. During provisioning, an Attestation Identity Key (AIK) is generated for each TPM, and the public part of the key is made available to entities that validate quotes. The TPM quote operation returns signed data and a signature. The data that is signed contains the PCRs selected for the operation, the composite hash for the selected PCRs, and a nonce provided as input, and used to prevent replay attacks. At provisioning time, the data that is signed is stored, not just the composite hash. The signature is discarded. An entity that wishes to evaluate a machine generates a nonce, and sends it along with the set of PCR used to generate the composite PCR hash at provisioning time. For this use of the TPM quote operation, the signed data is ignored, and the signature returned is used to val- idate the state of the TPM's PCRs. Given the signature, the evaluating entity replaces the nonce in the signed data generated at provi- sioning time, and checks to see if the signature is valid for the data. If so, this check ensures the selected PCRs contain values that match the ones measured during provisioning. A typical scenario for an enterprise using these tools follows. The tools expect AIKs to be referenced via one enterprise-wide Universally Unique Identifier (UUID). The program tpm_mkuuid creates one. For each machine being checked, an AIK is created using tpm_mkaik. The key blob produced is bound to the UUID on its machine using tpm_loadkey. The public key associated with the AIK is sent to the entities that verify quotes. Finally, the expected PCR composite hash is obtained using tpm_getpcrhash. When the expected PCR values change, a new hash can be generated with tpm_updatepcrhash. The program to obtain a quote, and thus measure the current state of the PCRs is tpm_getquote. The program that verifies the quote describes the same PCR composite hash as was measured initially is tpm_verifyquote. SEE ALSO
tpm_mkuuid(8), tpm_mkaik(8), tpm_loadkey(8), tpm_unloadkey(8), tpm_getpcrhash(8), tpm_updatepcrhash(8), tpm_getquote(8), tpm_verifyquote(8) Oct 2010 TPM QUOTE TOOLS(8)
All times are GMT -4. The time now is 09:36 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy