02-09-2012
Quote:
Originally Posted by
jlliagre
Is e1000g0 connected to the same switch as e1000g1 and e1000g2 ?
yes
:
Last edited by fpmurphy; 02-09-2012 at 10:14 AM..
9 More Discussions You Might Find Interesting
1. IP Networking
Hi Folks,
I've just installed solaris 8, but i cannot add my network card.
i've reboot the box, got into the configmode, and try'd to add a network card. but it doesn't work. I can't add a ip address to the card, an error occurs. Who do i add it.
Kind Regards (3 Replies)
Discussion started by: noripsni
3 Replies
2. UNIX for Advanced & Expert Users
All,
I have a need to software change the MAC address of a NIC in a Sparc Ultra 10 - I believe there is a command that allows to do this at boot up?
Is it a missing (to me) part of ifconfig ?
If so, what is the syntax?
All replies gratefully received !
Thanks
Andrew (3 Replies)
Discussion started by: wretch
3 Replies
3. Solaris
Installed solaris 10 and now i want to connect to internet,to make work this i need to NIC drivers can some body tell me is it possible to get drivers and how to install. I am dying to get rid of this problem..please help me (1 Reply)
Discussion started by: srinivas2828
1 Replies
4. Red Hat
I have an RHEL 5 server with 2 Broadcom on-board NICs and 2 quad-port Intel NICs. After I installed the OS, the Intel NICs became eth0-7, and the onboards are eth8 and eth9. I really need the onboard NICs to be eth0 and eth1 (I have plans to later remove the quad-ports and replace them with 10gE... (1 Reply)
Discussion started by: GKnight
1 Replies
5. Linux
Hi,
I would like to know how to change the speed of ethernet card in linux? as it is showing auto-neg using mii-tool -v eth0
and my requirement is 100mbps full duplex.
Regards,
Manoj (3 Replies)
Discussion started by: manoj.solaris
3 Replies
6. Solaris
Can someone point out which steps are to be done to get information if NIC on Solaris is malfunctioned and/or not working properly.
Since my Solaris knowledge is very modest, i would apreciate any help.
OS is Solaris 10 x86
Regards.
Peasant.
---------- Post updated at 11:57 AM... (0 Replies)
Discussion started by: Peasant
0 Replies
7. Solaris
Hi,
Hardware:
Mother board: Asus P5G4IC-M LX
On board NIC: PCIe Gigabite LAN
Kernel Ver.: SunOS 5.10 Generic_141445-09
I've NIC detection problem in Solaris 10. When I was trying to install in x86 machine, it was not asking for any Network settings which means it couldn't find NIC. But... (7 Replies)
Discussion started by: vicky86ind
7 Replies
8. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
9. UNIX for Advanced & Expert Users
Dear all,
I have a remote CentOS7 server that has two network cards. Each card has four ports and port one of card one was defined with the IP address assigned to the server. So far, so good and it's been working for over a year. We have now got cables sorted out so there are four paths... (4 Replies)
Discussion started by: rbatte1
4 Replies
LEARN ABOUT DEBIAN
shell-quote
SHELL-QUOTE(1p) User Contributed Perl Documentation SHELL-QUOTE(1p)
NAME
shell-quote - quote arguments for safe use, unmodified in a shell command
SYNOPSIS
shell-quote [switch]... arg...
DESCRIPTION
shell-quote lets you pass arbitrary strings through the shell so that they won't be changed by the shell. This lets you process commands
or files with embedded white space or shell globbing characters safely. Here are a few examples.
EXAMPLES
ssh preserving args
When running a remote command with ssh, ssh doesn't preserve the separate arguments it receives. It just joins them with spaces and
passes them to "$SHELL -c". This doesn't work as intended:
ssh host touch 'hi there' # fails
It creates 2 files, hi and there. Instead, do this:
cmd=`shell-quote touch 'hi there'`
ssh host "$cmd"
This gives you just 1 file, hi there.
process find output
It's not ordinarily possible to process an arbitrary list of files output by find with a shell script. Anything you put in $IFS to
split up the output could legitimately be in a file's name. Here's how you can do it using shell-quote:
eval set -- `find -type f -print0 | xargs -0 shell-quote --`
debug shell scripts
shell-quote is better than echo for debugging shell scripts.
debug() {
[ -z "$debug" ] || shell-quote "debug:" "$@"
}
With echo you can't tell the difference between "debug 'foo bar'" and "debug foo bar", but with shell-quote you can.
save a command for later
shell-quote can be used to build up a shell command to run later. Say you want the user to be able to give you switches for a command
you're going to run. If you don't want the switches to be re-evaluated by the shell (which is usually a good idea, else there are
things the user can't pass through), you can do something like this:
user_switches=
while [ $# != 0 ]
do
case x$1 in
x--pass-through)
[ $# -gt 1 ] || die "need an argument for $1"
user_switches="$user_switches "`shell-quote -- "$2"`
shift;;
# process other switches
esac
shift
done
# later
eval "shell-quote some-command $user_switches my args"
OPTIONS
--debug
Turn debugging on.
--help
Show the usage message and die.
--version
Show the version number and exit.
AVAILABILITY
The code is licensed under the GNU GPL. Check http://www.argon.org/~roderick/ or CPAN for updated versions.
AUTHOR
Roderick Schertler <roderick@argon.org>
perl v5.8.4 2005-05-03 SHELL-QUOTE(1p)