initialize a variable only once Post: 302596806

10 More Discussions You Might Find Interesting

1. Programming

variable initialize question

I have a question about C program for Unix: Do we have to intialize every variable before we use them in C? I thought we have to untill I found some programs are not intialize the variable before they were used.

2. Shell Programming and Scripting

Variable Initialize

Hi, i m trying to loop a variable value, Basically i m reading variable value from an input file and using in rest of the program. Bu my problem is when i first time read value and assign to variable it works fine, but in second read it concatinate second value to first value with a LF. I want to...

3. UNIX for Dummies Questions & Answers

nslookup *** Can't initialize resolver

Has anyone seen this message before? I have a DNS problem. Recently DNS has been moved to two new servers, which I can ping. I changed the /etc/resolv.conf to point to these boxes but now I get the *** Can't initialize resolver message. Any ideas?

4. SCO

initialize lp job

I use SCO UNIX from 2 years I need a command or procedure to make all log files empty and restart all counters like lp job number :( :confused: :(

5. HP-UX

Can not initialize the floppy

Hello Everyone, Has anyboby ever come across the problem when fd refuses to get initialised. I try to use mediainit command, the fd is being accessed (the fd's LIT is green for some secs) but then I get the message - "Initialize media command failed - permission denied" I checked the diskette,...

6. Shell Programming and Scripting

initialize file to zero

hi can anyone tell how to initialize a file to zero

7. Shell Programming and Scripting

Initialize a variable

Hi All, Please can you advise on how can I initialize a variable with a line. Suppose i want to initialize x with line redirects.www.virginatlantic.com.conf Best Regards, Shazin

8. SCO

How to initialize tape drive

Hi all Just connected a SCSI tape drive to our ScoUnix server running Unixware 7.0.1. The ID assigned to it is 3. When I open ArcServe it is saying that tape drive is not found and I cannot configure it. How can I make the tape drive accessible to the system? Thanks!

9. Red Hat

Fedora Initialize disklabel

What is the point of Fedora Initialize disklabel and how does it work? How do I check what my current Fedora's disklabel is initialized to?

10. UNIX for Dummies Questions & Answers

Initialize Variable Using awk Expression

Hello All, What i am trying to do is read the input file delimited by pipe and do further logic like simulating the for loop but using awk not sure if this a right approach but as i was told doing "for i in `cat $file`" is an over kill so trying to replicate the same thing using awk script below....

LEARN ABOUT SUNOS

service

SERVICE(8)						      System Manager's Manual							SERVICE(8)

NAME

       service - run a System V init script

SYNOPSIS

       service SCRIPT COMMAND [OPTIONS]

       service --status-all

       service --help | -h | --version

DESCRIPTION

       service	runs  a System V init script or systemd unit in as predictable an environment as possible, removing most environment variables and
       with the current working directory set to /.

       The SCRIPT parameter specifies a System V init script, located in /etc/init.d/SCRIPT, or the name of a systemd unit.  The  existence  of  a
       systemd unit of the same name as a script in /etc/init.d will cause the unit to take precedence over the init.d script.	The supported val-
       ues of COMMAND depend on the invoked script. service passes COMMAND  and OPTIONS to the init script unmodified. For systemd  units,  start,
       stop, status, and reload are passed through to their systemctl/initctl equivalents.

       All scripts should support at least the start and stop commands.  As a special case, if COMMAND is --full-restart, the script is run twice,
       first with the stop command, then with the start command.

       service --status-all runs all init scripts, in alphabetical order, with the status command. The status is [ + ] for running services, [ - ]
       for stopped services and [ ? ] for services without a status command.  This option only calls status for sysvinit jobs.

EXIT CODES

       service calls the init script and returns the status returned by it.

FILES

       /etc/init.d
	      The directory containing System V init scripts.

       /{lib,run,etc}/systemd/system
	      The directories containing systemd units.

ENVIRONMENT

       LANG,  LANGUAGE,  LC_CTYPE, LC_NUMERIC, LC_TIME, LC_COLLATE, LC_MONETARY, LC_MESSAGES, LC_PAPER, LC_NAME, LC_ADDRESS, LC_TELEPHONE, LC_MEA-
       SUREMENT, LC_IDENTIFICATION, LC_ALL, TERM, PATH
	      The only environment variables passed to the init scripts.

SEE ALSO

       /etc/init.d/skeleton
       update-rc.d(8)
       init(8)
       invoke-rc.d(8)
       systemctl(1)

AUTHOR

       Miloslav Trmac <mitr@redhat.com>, Petter Reinholdtsen <pere@hungry.com>

       Licence: GNU Public Licence v2 (GPLv2)

COPYRIGHT

       2006 Red Hat, Inc.,  Petter Reinholdtsen <pere@hungry.com>

Jan 206 																SERVICE(8)

10 More Discussions You Might Find Interesting

1. Programming

variable initialize question

Discussion started by: whatisthis

2. Shell Programming and Scripting

Variable Initialize

Discussion started by: coolbudy

3. UNIX for Dummies Questions & Answers

nslookup *** Can't initialize resolver

Discussion started by: korfnz

4. SCO

initialize lp job

Discussion started by: sharina