01-20-2012
You can rule out a lot of internal hard disk controllers by preventing ahci.ko from loading, if that's built as a module and not built-in. This also rules out a lot of internal cdroms though.
You could try disabling your hard-drive controller in the BIOS.
If you're able to run any commands on the clonezilla disk before clonezilla starts doing things, how about chmod 000 /dev/sda* ? Might fail if clonezilla runs everything as root, but worth a shot.
You could also use a machine with no internal hard drives!
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Will some one tell me what this means.
"warning: ida 0 <slot 6> : command timed out on dev 1/42 blk 4824290 logical unit=0 blocks=5512102, size 2, cmd=0x20."
I'm running SCO 505 on a proliant 1600r.
Thnank you in advance. (3 Replies)
Discussion started by: franruiz
3 Replies
2. Linux
I am using an Acer Aspire 4720Z with two partitions C and D. Windows is installed on C and I decided to install Red Hat Linux 9 in partition D. The two partitions are in NTFS file system. During my installation of the the Linux, a prompt was displayed on screen with the message: "No hard drives... (2 Replies)
Discussion started by: tamcomng
2 Replies
3. Filesystems, Disks and Memory
Any recommend manufacturers for an internal SCSI tape drive in my FreeBSD 7.0 home server? Besides RAID-1, I'm not backing-up, but man, are they expensive! What makes a tape drive so darn pricy? There is no way I can afford a new drive so I'll start looking on eBay and craigslist to see if there... (3 Replies)
Discussion started by: Aaron Van
3 Replies
4. Solaris
Version: solaris 10 x86
I just got a western digital external harddrive formated with fat 32. this drive came with some setup files which is meant for windows or mac.
I want to reformat and partition this drive into two ( for solaris and windows) such that the setup files will still be there... (2 Replies)
Discussion started by: seyiisq
2 Replies
5. Filesystems, Disks and Memory
Folks;
I just added 2 physical new hard drives to my SUSE server. My server is already running SUSE 10.3 version.
Is there a command i can use to add the new space or even see if the system can sees them? (3 Replies)
Discussion started by: Katkota
3 Replies
6. UNIX for Dummies Questions & Answers
Hello, I need to write a program which sets server's ip address, router, network mask. Program also should set if it is an internal or external ip. Maybe someone can help me ? Any information from u is very useful :b:
I stopped at .. :(
#!/bin/sh
A=`hostname -i`
echo "server ip address is $A"... (4 Replies)
Discussion started by: zagaruika
4 Replies
7. Solaris
I have a T2000 Sun-Fire server. I have 2 sets of drives in a raid 1. Lets call them Set A and Set B. I had Set A installed and working. I needed a new install so I so build up Set B. After some time I wanted to put Set A back in the server. Now the system will not boot off of Set A. I tried to boot... (7 Replies)
Discussion started by: stu1811
7 Replies
8. Hardware
Hello everyone. I have a question which I may know the answer to, I'm just looking for a confirmation. When it comes to the MBR of a hard drive, i've read in multiple sources that it's always located in the first sector of the hard drive. Is the MBR there from the factory? When I buy a new blank... (3 Replies)
Discussion started by: Lost in Cyberia
3 Replies
9. Solaris
Hi,
I have two SCSI Hard Drives in a Sun Solaris 8 server as shown below. I would like to access Disk1 and look at its contents, directory structure and files. How do I change my default directory from Disk 0 to Disk 1 and vice versa?
Thank you. (5 Replies)
Discussion started by: ssabet
5 Replies
10. UNIX for Beginners Questions & Answers
Ok so i thought i was smart but i can tell I need some help. I am playing around with understanding lvm and adding disks to a linux box. I added a disk and then ran what i thought were commands to add this disk to the box but I think I messed up and would like some help. My question is did i... (5 Replies)
Discussion started by: cptkirkh
5 Replies
IOSTAT(1) General Commands Manual IOSTAT(1)
NAME
iostat - report I/O statistics
SYNOPSIS
iostat [ drives ] [ interval [ count ] ]
DESCRIPTION
Iostat iteratively reports the number of characters read and written to terminals per second, and, for each disk, the number of transfers
per second, kilobytes transferred per second, and the milliseconds per average seek. It also gives the percentage of time the system has
spent in user mode, in user mode running low priority (niced) processes, in system mode, and idling.
To compute this information, for each disk, seeks and data transfer completions and number of words transferred are counted; for terminals
collectively, the number of input and output characters are counted. Also, each sixtieth of a second, the state of each disk is examined
and a tally is made if the disk is active. From these numbers and given the transfer rates of the devices it is possible to determine
average seek times for each device.
The optional interval argument causes iostat to report once each interval seconds. The first report is for all time since a reboot and
each subsequent report is for the last interval only.
The optional count argument restricts the number of reports.
If more than 4 disk drives are configured in the system, iostat displays only the first 4 drives, with priority given to Massbus disk
drives (i.e. if both Unibus and Massbus drives are present and the total number of drives exceeds 4, then some number of Unibus drives will
not be displayed in favor of the Massbus drives). To force iostat to display specific drives, their names may be supplied on the command
line.
FILES
/dev/kmem
/vmunix
SEE ALSO
vmstat(1)
4th Berkeley Distribution April 29, 1985 IOSTAT(1)