Sponsored Content
Operating Systems AIX Powerha on P595 and Blade HX5 Type 787 Post 302590996 by zxmaus on Wednesday 18th of January 2012 07:47:49 AM
Old 01-18-2012
actually powerha doesnt overly care if its on one or two frames - it doesnt check the underlying system. But for the obvious reasons (if your frame goes down, your cluster does too) it might not be such a great idea Smilie

Regards
zxmaus
 

5 More Discussions You Might Find Interesting

1. AIX

How to know the hardware configuration on P595 LAPRs

The p595 have 6 Lpars, not all hardware resource assigned to 6 lpars. which command can list all hardware configuration on p595? Do I need go to each lapr to list? (2 Replies)
Discussion started by: rainbow_bean
2 Replies

2. AIX

p595 LPAR no longer sees SAN boot disk

Hello, we have a wierd and urgent problem, with a few of our p595 LPARs running AIX 5.3. The LPARs ran AIX 5.3 TL 7 and booted off EMC SAN disks, using EMC Powerpath. Every boot we run "pprootdev on" and "pprootdev fix". We can issue "bosboot -a" and we can reboot the machines. Now, on two... (2 Replies)
Discussion started by: rwesterik
2 Replies

3. AIX

Virtualizing the Fiber card (VFC) on P595

Hi, We have a P595 machine with a dual port Fiber card per VIOs. We have two VIOs in the box. VIO1: ---> 2 port Fiber Card VIO2: ---> 2 port Fiber Card One port on each fiber card is utilized. Connected to SAN switches. We are getting all disks from SAN both for VIOs and LPARs. Now... (0 Replies)
Discussion started by: aixromeo
0 Replies

4. AIX

HMC Hardware Discovery does not work for p595 frames

Hi, I require help with hardware discovery while running a command from an HMC with firmware V7.3.5 SP 3. The two frames I am running the command for are p 5 595's. Command input: lshwres -m swdc-c02-9119-595-SN02780CF -r io --rsubtype slotchildren -F lpar_name Error output: The managed... (1 Reply)
Discussion started by: AIXNEWBIE62
1 Replies

5. Red Hat

How to know full width blade or half width blade?

HI, How do we figure out if the server is half blade server or full blade server? Anything we need to look at to know on this? thanks in advance (9 Replies)
Discussion started by: snchaudhari2
9 Replies
XPILOT-NG-REPLAY(6)						       Games						       XPILOT-NG-REPLAY(6)

NAME
xpilot-ng-replay - Playback an XPilot session. SYNOPSIS
xpilot-ng-replay [options] filename DESCRIPTION
If filename is a dash - then standard input is used. Valid options are: -scale "factor" Set the scale reduction factor for saving operations. Valid scale factors are in the range [0.01 - 1.0]. -linewidth "width" use a fixed linewidth "width" for drawing all lines -gamma "factor" Set the gamma correction factor when saving scaled frames. Valid gamma correction factors are in the range [0.1 - 10]. -compress Save frames compressed using the "compress" program. -fps "value", -FPS "value" Set the number of frames per second used for replay and recording. -play Start playing immediately. -loop Loop after playing. -debug -verbose -help -version In addition to the pushbuttons you can use the following keys: f - move forwards to the next frame. b - move backwards to the next frame. z - move backwards to the first frame. [ - mark the current frame as the first frame to be saved. ] - mark the current frame as the last frame to be saved. * - save the marked frames in PPM format. WARNING: saving many frames takes HUGE amounts of diskspace! & - save the marked frames in XPilot Recording format. q - quit the program. xpilot.sourceforge.net November 2011 XPILOT-NG-REPLAY(6)
All times are GMT -4. The time now is 06:21 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy