Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: How to get into BIOS and disable NICS?
Special Forums Hardware How to get into BIOS and disable NICS? Post 302579005 by jgt on Saturday 3rd of December 2011 07:45:35 PM
Old 12-03-2011
What model?
 

10 More Discussions You Might Find Interesting

1. AIX

Merge NICs

Hi friends, I installed oracle 10g (10.2.0.2) RAC on 2 IBM p5 570 servers running AIX 5.3ML04 and HACMP5.2 (used Raw devices, not used GPFS). Each server has 4 x 1Gbps ethernet cards (NICs), en0 and en1 for boot address, en2 and en3 for oracle interconnect. Now i want to merge 2 NICs (en2 and... (1 Reply)
Discussion started by: bong02
1 Replies

2. IP Networking

FreeBSD and two NICs

FreeBSD 4.8, Apache 1.3.27 - two NICs, one with a real-world IP plugged into a switch outside the PIX firewall, the other with a private IP plugged into a switch inside the PIX firewall. Apache listens on both IPs. my domain is mydomain.org. so in /etc/rc.conf i have something like this (these... (10 Replies)
Discussion started by: ednix
10 Replies

3. Solaris

How many NICS do I have?

Hi, is there a way in Solaris 8 to determine how many total NIC's say a Sun Sparc box has installed - plumbed or unplumbed - and find out its capable network speeds and MAC address? I know ifconfig -a but that only shows the plumbed and used interfaces. thx cc (2 Replies)
Discussion started by: bigapple100
2 Replies

4. Linux

Two NICs one IP address

I'm looking for a way in RHL 5.1 to use two NICs on one host with two physical IP addresses and map them under one virtual IP address, i.e. NIC 1 10.10.10.1 NIC2 10.10.10.2 VIP 192.168.10.1 Basically I want either one of the NICs to ARP for the VIP. No load balancing required just HA. (2 Replies)
Discussion started by: wschmied
2 Replies

5. UNIX for Dummies Questions & Answers

How to find about NICs installed

Hi; Is there a way to determine for sure how many NIC ports installed on my Linux box? I tried to run "lspci" but not sure about the results, it's not clear. Below are the results when i run both "ifconfig" & "lspci" on my Linux box i hope someone can help me finding the actual numbers of... (1 Reply)
Discussion started by: Katkota
1 Replies

6. Shell Programming and Scripting

How to disable Enable/Disable Tab Key

Hi All, I have bash script, so what is sintax script in bash for Enable and Disable Tab Key. Thanks for your help.:( Thanks, Rico (1 Reply)
Discussion started by: carnegiex
1 Replies

7. Red Hat

SSL/TLS renegotiation DoS -how to disable? Is it advisable to disable?

Hi all Expertise, I have following issue to solve, SSL / TLS Renegotiation DoS (low) 222.225.12.13 Ease of Exploitation Moderate Port 443/tcp Family Miscellaneous Following is the problem description:------------------ Description The remote service encrypts traffic using TLS / SSL and... (2 Replies)
Discussion started by: manalisharmabe
2 Replies

8. Red Hat

Enter Bios and disable onboard NICS?

Hi, I have to get into BIOS and disable onbaord NICS for an IBM server, can someone please help me out. I tried hitting F1 when reboot to get into BIOS, but it seems like a setup screen and I dont see any option to disable NICS? Thanks Sam (0 Replies)
Discussion started by: sam4919
0 Replies

9. IP Networking

Networking 2 NICs

Hi all, Host - Ubuntu 12.04 desktop 64bit Virtualizer - Oracle VirtualBox 2 NICs Where can I find relevant document to set up 2 NICs, one for inward bound and another for outward bound, separate channel, both connected to the same router Would following document be appropriate for my... (1 Reply)
Discussion started by: satimis
1 Replies

10. UNIX for Dummies Questions & Answers

Linux with two NICs

Hello All, I have Linux box with two interface cards. Every card has it's own IP Address and Gateway, IP addresses are from different subnets. eth0 192.168.1.10/24 GW 192.168.1.1 eth1 192.168.2.10/24 GW 192.168.2.1 Third PC is located in 192.168.13.0/24 network and is trying to access... (2 Replies)
Discussion started by: AndreiM
2 Replies

LEARN ABOUT NETBSD

trm

TRM(4)							   BSD Kernel Interfaces Manual 						    TRM(4)

NAME

     trm -- Tekram TRM-S1040 ASIC based PCI SCSI host adapter driver

SYNOPSIS

     trm* at pci? dev ? function ?
     scsibus* at trm?

DESCRIPTION

     The trm driver supports PCI SCSI host adapters based on the Tekram TRM-S1040 SCSI ASIC.

HARDWARE

     Supported SCSI controllers include:

	   Tekram DC-315 PCI Ultra SCSI adapter without flash BIOS and internal SCSI connector

	   Tekram DC-315U PCI Ultra SCSI adapter without flash BIOS

	   Tekram DC-395U PCI Ultra SCSI adapter with flash BIOS

	   Tekram DC-395UW PCI Ultra-Wide SCSI adapter with flash BIOS

	   Tekram DC-395F PCI Ultra-Wide SCSI adapter with flash BIOS and 68-pin external SCSI connector

     For Tekram DC-390 PCI SCSI host adapter, use pcscp(4) driver.

     For Tekram DC-310/U and DC-390U/UW/F PCI SCSI host adapters, use siop(4) driver.

SEE ALSO

     cd(4), ch(4), intro(4), pci(4), scsi(4), sd(4), ss(4), st(4), uk(4), scsipi(9)

     http://www.tekram.com/

AUTHORS

     The trm driver was originally written for NetBSD 1.4/i386 by Erich Chen of Tekram Technology, and Rui-Xiang Guo rewrote the driver to use
     bus_space(9) and bus_dma(9) for NetBSD 1.6.

BSD
								 November 6, 2001							       BSD
All times are GMT -4. The time now is 08:15 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy