12-01-2011
Thanks Jao and Duke....
It is a non global zone , will that be a reason for this ....even I dont find /etc/system file in this.
Rgds
Rj
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello there !!!
I am going to install solaris 8 on brand new hard disk, which i just attatched with computer.
Hard disk is already formated or do i have to use some kind of fdisk prior to install solaris ?
OR solaris automatically format this new hard disk ?
How does this work with... (2 Replies)
Discussion started by: abidmalik
2 Replies
2. UNIX for Dummies Questions & Answers
Hi Friends !
How long does it take to format a hard disk under Solaris ?
Once the format starts, what data will be cleared or deleted first ? i.e whether the OS is cleared or all the data other than OS is cleared first ?
Then, if the format starts and the power goes off, can i retrieve data?... (1 Reply)
Discussion started by: mrgubbala
1 Replies
3. Solaris
Hi,
am a newbie at solaris. Need advice and help on this.
1) How do I break the mirror between 2 hard disks. (wish to keep 1 good hard disk as backup)
2) After remove 1 hard disk and put in new hard disk, how do I initialise or fomat the new hard disk?
3) How do I put back the backup... (3 Replies)
Discussion started by: chongkls77
3 Replies
4. Solaris
Hi All,
I have new Netra 240 box which is not detecting its harddisk equiped with itse same har disk are detected when I swap with another machine.
Same time If I swap hardisk of other machine to this Netra 240 box, also do not work. I have checked chassis, cabling etc and all looks fine. ... (1 Reply)
Discussion started by: xpwistler
1 Replies
5. Solaris
Hi Peeps,
Trying to run analyze and verify on a disk, it won't as it's telling me the disk is write protected. Anyone got any ideas on how to remove the write protection????
Didn't even know you could write protect hard disks.
Thanks for any advice
Marty (2 Replies)
Discussion started by: callmebob
2 Replies
6. Solaris
I installed Solaris 10 on this Dell 5150 with only 1 SATA hard drive setup, all went well, and I could view the disk in the disk management window.
However, I setup a 2nd hard drive, identical to 1st drive. Solaris wont recognize it and gives an error when trying to view disks in disk management... (5 Replies)
Discussion started by: Joncamp
5 Replies
7. Solaris
Hi Gurus,
I have difficulty in configuring removable hard disk in Solaris 8.
I have connected hard disk to machine but I do not know how to configure it.
Kindly tell me, how should I configure it .. so that I can create a mount point on this and write files to them.
Regards
Srini (7 Replies)
Discussion started by: sri243
7 Replies
8. Linux
Hi all,
I'm kind of new to programming in Linux & c/c++. I'm currently writing a FileManager using Ubuntu Linux(10.10) for Learning Purposes. I've got started on this project by creating a loopback device to be used as my virtual hard disk. After creating the loop back hard disk and mounting it... (23 Replies)
Discussion started by: shen747
23 Replies
9. Solaris
Dear All,
I have a task of resizing the Solaris Partitions.
This server contains SVM. Kindly let me know the steps in resizing the partitions and precautions.
Regards
Rj (3 Replies)
Discussion started by: jegaraman
3 Replies
10. UNIX for Dummies Questions & Answers
Hi,
How can i use a old window 200Gb IDE harddisk on Solaris8.
At the Solaris 8 install utility, it could only detect 50Mb for space !
Is the format wrong ?
Do i need to re-do the partition ?
I am using a Sunblade150 with solaris8
Thank u for the help... (1 Reply)
Discussion started by: Snubber
1 Replies
rem_drv(1M) rem_drv(1M)
NAME
rem_drv - remove a device driver from the system
SYNOPSIS
rem_drv [-b basedir] device_driver
The rem_drv command informs the system that the device driver device_driver is no longer valid. If possible, rem_drv unloads device_driver
from memory. rem_drv also updates the system driver configuration files.
If rem_drv has been executed, the next time the system is rebooted it automatically performs a reconfiguration boot (see kernel(1M)).
The following options are supported:
-b basedir Sets the path to the root directory of the diskless client. Used on the server to execute rem_drv for a client. The client
machine must be rebooted to unload the driver.
Note - The root file system of any non-global zones must not be referenced with the -b option. Doing so might damage the
global zone's file system, might compromise the security of the global zone, and might damage the non-global zone's
file system. See zones(5).
Example 1: Removing the sd Driver
The following example removes the sd driver from use:
example% rem_drv sd
Example 2: Removing a Diskless Client
The following example removes the driver from the sun1 diskless client. The driver is not uninstalled or unloaded until the client machine
is rebooted.
example% rem_drv -b /export/root/sun1 sd
Note the caveat on the use of the -b option in the description of that option, above.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
add_drv(1M), kernel(1M), update_drv(1M), attributes(5), devfs(7FS)
6 Apr 2005 rem_drv(1M)