12-01-2011
solaris hard disk not detected
Dear all,
I have a Sol 10 server.
When I put df -h , it is showing the mount points of all file systems,
but when I format the server it is showing the below output
bash-3.00# format
Searching for disks...done
No disks found!
Pl let me know what is the problem for this.
Rgds
rj
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello there !!!
I am going to install solaris 8 on brand new hard disk, which i just attatched with computer.
Hard disk is already formated or do i have to use some kind of fdisk prior to install solaris ?
OR solaris automatically format this new hard disk ?
How does this work with... (2 Replies)
Discussion started by: abidmalik
2 Replies
2. UNIX for Dummies Questions & Answers
Hi Friends !
How long does it take to format a hard disk under Solaris ?
Once the format starts, what data will be cleared or deleted first ? i.e whether the OS is cleared or all the data other than OS is cleared first ?
Then, if the format starts and the power goes off, can i retrieve data?... (1 Reply)
Discussion started by: mrgubbala
1 Replies
3. Solaris
Hi,
am a newbie at solaris. Need advice and help on this.
1) How do I break the mirror between 2 hard disks. (wish to keep 1 good hard disk as backup)
2) After remove 1 hard disk and put in new hard disk, how do I initialise or fomat the new hard disk?
3) How do I put back the backup... (3 Replies)
Discussion started by: chongkls77
3 Replies
4. Solaris
Hi All,
I have new Netra 240 box which is not detecting its harddisk equiped with itse same har disk are detected when I swap with another machine.
Same time If I swap hardisk of other machine to this Netra 240 box, also do not work. I have checked chassis, cabling etc and all looks fine. ... (1 Reply)
Discussion started by: xpwistler
1 Replies
5. Solaris
Hi Peeps,
Trying to run analyze and verify on a disk, it won't as it's telling me the disk is write protected. Anyone got any ideas on how to remove the write protection????
Didn't even know you could write protect hard disks.
Thanks for any advice
Marty (2 Replies)
Discussion started by: callmebob
2 Replies
6. Solaris
I installed Solaris 10 on this Dell 5150 with only 1 SATA hard drive setup, all went well, and I could view the disk in the disk management window.
However, I setup a 2nd hard drive, identical to 1st drive. Solaris wont recognize it and gives an error when trying to view disks in disk management... (5 Replies)
Discussion started by: Joncamp
5 Replies
7. Solaris
Hi Gurus,
I have difficulty in configuring removable hard disk in Solaris 8.
I have connected hard disk to machine but I do not know how to configure it.
Kindly tell me, how should I configure it .. so that I can create a mount point on this and write files to them.
Regards
Srini (7 Replies)
Discussion started by: sri243
7 Replies
8. Linux
Hi all,
I'm kind of new to programming in Linux & c/c++. I'm currently writing a FileManager using Ubuntu Linux(10.10) for Learning Purposes. I've got started on this project by creating a loopback device to be used as my virtual hard disk. After creating the loop back hard disk and mounting it... (23 Replies)
Discussion started by: shen747
23 Replies
9. Solaris
Dear All,
I have a task of resizing the Solaris Partitions.
This server contains SVM. Kindly let me know the steps in resizing the partitions and precautions.
Regards
Rj (3 Replies)
Discussion started by: jegaraman
3 Replies
10. UNIX for Dummies Questions & Answers
Hi,
How can i use a old window 200Gb IDE harddisk on Solaris8.
At the Solaris 8 install utility, it could only detect 50Mb for space !
Is the format wrong ?
Do i need to re-do the partition ?
I am using a Sunblade150 with solaris8
Thank u for the help... (1 Reply)
Discussion started by: Snubber
1 Replies
LEARN ABOUT CENTOS
gnome-disks
GNOME-DISKS(1) gnome-disk-utility GNOME-DISKS(1)
NAME
gnome-disks - the GNOME Disks application
SYNOPSIS
gnome-disks [OPTIONS]
DESCRIPTION
gnome-disks is the command to launch the GNOME Disks application. Disks provides a way to inspect, format, partition and configure disks
and block devices.
The Disks application is single-instance. What this means is that if the application is not already running when the gnome-disks command is
invoked, it will get launched and the command invocation will block until the application exits. Otherwise the existing application
instance will be used and the gnome-disks command will exit immediately.
OPTIONS
The following options are understood:
--block-device DEVICE
Switches to the Disks application and selects the block device given by DEVICE (for example, /dev/sda).
--block-device DEVICE --format-device [--xid WINDOW-ID]
Shows the "Format Volume" dialog for the block device given by DEVICE (for example, /dev/sdb1). If WINDOW-ID is given, makes the dialog
transient to the given XID.
--help
Prints a short help text and exits.
AUTHOR
Written by David Zeuthen <zeuthen@gmail.com> with a lot of help from many others.
BUGS
Please send bug reports to either the distribution bug tracker or the upstream bug tracker at
https://bugzilla.gnome.org/enter_bug.cgi?product=gnome-disk-utility.
SEE ALSO
gnome-disk-image-mounter(1), udisks(8)
GNOME
March 2013 GNOME-DISKS(1)