Sponsored Content
Full Discussion: The simplest network driver
Top Forums Programming The simplest network driver Post 302577563 by Corona688 on Tuesday 29th of November 2011 10:48:58 AM
Old 11-29-2011
No, I don't. It was an option that had to be forced with insmod/modprobe like I said.

I don't see the right messages in that driver, it may be a different one. I'll look for it.

---------- Post updated at 09:48 AM ---------- Previous update was at 09:44 AM ----------

eepro.c has these lines:

Code:
                printk(KERN_WARNING "eepro_init_module: Probe is very dangerous in ISA boards!\n");
                printk(KERN_WARNING "eepro_init_module: Please add \"autodetect=1\" to force probe\n");

 

8 More Discussions You Might Find Interesting

1. Programming

Network device driver

HI, I am writing a network device driver for RTL8139c card on 2.6.18 kernel ... I am facing few queries listed below 1. Can i able to at all write a driver for RTL8139C or Realtek had designed new chip for 2.6 series kernel? 2. If no then which driver file 2.6.18 uses .. Is it 8139too.c or... (1 Reply)
Discussion started by: niketan
1 Replies

2. Solaris

network driver cpu usage

Hello all, Needed a suggestion from you all, if you know anything about this stuff. We have a high network traffic application. Close to around 700Meg /sec on one NIC. When the traffic is around 200Meg on the NIC, the VCPU(not the CPU, cause we have 24 VCPU) utilization by the NIC driver... (5 Replies)
Discussion started by: Naanu
5 Replies

3. Solaris

Installing Network on Computer, might be driver

Hi All, Just completing my second Solaris installation, in the previous one which was on a Dell X64 machine, I went through the Network configuration setting, on the current computer which I am installing Solaris on, its a custom built machine and for some reason, I didnt see the screen where I... (1 Reply)
Discussion started by: platforminc
1 Replies

4. Solaris

network driver not detecting in solaris 10 X86 on HPDL380G5 Server

I have installed solaris10 x86 on HP DL380 G5 Server, but network card is not getting detected. i have installed the network driver, downloaded from the following link HP ProLiant DL380 G5 Server series- Download drivers and software - HP Business Support Center Can any one suggest me how to... (1 Reply)
Discussion started by: raj.chinnu
1 Replies

5. Red Hat

How to know whether the network driver alredy installed in my system

I am using NVIDIA nforce: Networking controllers And Redhat enterprice linux ws version 4 32 bit: OS I want to connect my system to Broadband internet using linux. From where can I download the driver for nertwork. How to know whether the network driver alredy installed in my system. ... (0 Replies)
Discussion started by: rijas
0 Replies

6. Solaris

Can I Install the Gani Network Driver Using the Application that Came on the CD?

When I boot up the Solaris 10 5/09 install CD and select 'Solaris' from the GRUB menu that comes up, a menu loads. Option 5 is 'Apply Driver Updates'. Can I install the Gani driver using that? I tried using the tar file (the way it came) that I wrote to a floppy but when I asked it to look at the... (8 Replies)
Discussion started by: Bradj47
8 Replies

7. UNIX for Dummies Questions & Answers

Simulated driver for Network Interface Adapter

Hi all, I got sort of a task to do. I have to write in C "simulated network driver". What does it mean? - It has to run on all network adapters - It has to be as simple as it can be - It has to run on all linux distributions (or at least most of them) - It does not have to run a network... (4 Replies)
Discussion started by: Chrisdot
4 Replies

8. Programming

Compiling virtual network adapter driver problem (net_device struct)

Hi, I found on linuxgazette.net/93/bhaskaran.html page very useful sample of virtual driver (not connected to real hardware). I try to compile it with no effect. So: I got fresh Ubuntu 9.10 (kernel 2.6.31-14) My source is saved in networkAdapter.c file in /usr/src/myModules directory. I... (21 Replies)
Discussion started by: Chrisdot
21 Replies
INSMOD(8)                                                             insmod                                                             INSMOD(8)

NAME
insmod - Simple program to insert a module into the Linux Kernel SYNOPSIS
insmod [filename] [module options...] DESCRIPTION
insmod is a trivial program to insert a module into the kernel. Most users will want to use modprobe(8) instead, which is more clever and can handle module dependencies. Only the most general of error messages are reported: as the work of trying to link the module is now done inside the kernel, the dmesg usually gives more information about errors. COPYRIGHT
This manual page originally Copyright 2002, Rusty Russell, IBM Corporation. Maintained by Jon Masters and others. SEE ALSO
modprobe(8), rmmod(8), lsmod(8), modinfo(8) AUTHORS
Jon Masters <jcm@jonmasters.org> Developer Lucas De Marchi <lucas.de.marchi@gmail.com> Developer kmod 01/28/2018 INSMOD(8)
All times are GMT -4. The time now is 08:52 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy