11-13-2011
Quote:
Originally Posted by
nagarjunatula
hi polar,
what is ur server model?
depends upon the model we have to configure.if it is power6 520 then k.
is ur server is managed through hmc?
if it is connected, select the server and go to hardware information.tjhere you will locate the physical ethernet ports, then select the port and configure it.set the promiscous mode for the port which u have selected.
Power model 720 with HMC.
Means that i configure the particular client LPARs for particular physical port(ent0, ent1, ent2, ent3) on 'Promiscous LPAR'? so that 4 set of SEA configure can be used without any problems?
(p.s : This adapter card is not HEA)
Last edited by polar; 11-13-2011 at 07:07 AM..
Reason: correction
10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
Okay, not sure if it can be done, I would think it could be done and I'm just having a hard time with it.
fun_close_wait(){
ipVar="${1} ${2}"
portVar=`cat "${5}" | cut -d' ' -f 1`
for ip in $ipVar
do
for port in $portVar
do
netstatVar=`netstat -n | grep... (4 Replies)
Discussion started by: cbo0485
4 Replies
2. AIX
I am trying to create a SEA on a LHEA port and it gives me error
lsdev -Cc adapter:
ent0 logical host ethernet port (l-hea)
ent1 virtual I/O ethernet adapter
mkvdev -sea ent0 -vadapter ent1 -default ent1 -defaultid 199
method error (/usr/lib/methods/cfgsea):
Failed to configure SEA... (0 Replies)
Discussion started by: filosophizer
0 Replies
3. AIX
Hi Guys,
I'm getting the below error while trying to create a SEA adapter in VIOS
$ mkvdev -sea ent0 -vadapter ent2 -default ent2 -defaultid 1
... (4 Replies)
Discussion started by: kkeng808
4 Replies
4. AIX
Hi all,
I set up the following configuration on my system:
- An LPar with a virtual adapter, first one with a vlan id=703 and id port=13.
- The first adapter have to connect to a VIOS in which i configured an SEA.
So, the VA is set up on interface ent2, SEA on ent29 (by linking a... (0 Replies)
Discussion started by: idro
0 Replies
5. Linux
Hi,
Can we set password for linux in non-interactive mode.
I didn't find suitable option for this in man page.
If we wnter "passwd" command, it will tell "Enter password" and "Re-enter password". i wanted to run this step in a script, and i don't want to use "expect" so i am looking for a single... (8 Replies)
Discussion started by: successlin
8 Replies
6. AIX
I am trying to install a VIOS pair with a load-sharing SEA adapter, following this recipe from Developerworks. Without load-sharing everything went fine and worked as expected, but somehow i am a bit lost and the first tries with "ha_mode=sharing" didn't work at all.
Here is the situation:
I... (6 Replies)
Discussion started by: bakunin
6 Replies
7. AIX
Hello,
Lets say for simplicity that I do not use any vlan config inside my server - one lpar group use hea physical port1, another group hea physical port2. Physical port1 configured as vlan1 on external switch, physical port2 as vlan2.
What is the common practice - should I isolate my vios... (0 Replies)
Discussion started by: vilius
0 Replies
8. AIX
i want configure a SEA over my vios ,
i have a message error :
Method error (/usr/lib/methods/cfgsea):
Failed to configure SEA with return code 1 and SEA-specific error code 10:
Detailed info: Setting real adapter ent1 in promiscuous mode failed... (5 Replies)
Discussion started by: hedou
5 Replies
9. AIX
hello,
what will happen if i try to move sea of my 1 vio server to standby( using chdev command), when sea of other vio server is already in standby mode? (1 Reply)
Discussion started by: amvineeth
1 Replies
10. AIX
Hello,
I found that the packet counts given by entstat -d SEA is not the same as the total of the packet counts given by seastat -d SEA for the same interval of time.
Do anyone have an explanation for the difference. We recently got a recommendation that the throughput on an SEA should not... (5 Replies)
Discussion started by: N8R
5 Replies
LEARN ABOUT OPENSOLARIS
scconf_transp_adap_bge
scconf_transp_adap_bge(1M) System Administration Commands scconf_transp_adap_bge(1M)
NAME
scconf_transp_adap_bge - configure the bge transport adapter
DESCRIPTION
Note -
Beginning with the Sun Cluster 3.2 release, Sun Cluster software includes an object-oriented command set. Although Sun Cluster software
still supports the original command set, Sun Cluster procedural documentation uses only the object-oriented command set. For more infor-
mation about the object-oriented command set, see the Intro(1CL) man page.
You can configure bge adapters as cluster transport adapters. These adapters can only be used with the dlpi transport type. The bge adapter
is VLAN capable.
The bge adapter connects to a transport switch or to another bge adapter on a different node. In either case, the connection is made
through a transport cable.
When a transport switch is used and the endpoints of the transport cable are configured by using the scconf command, the scinstall command,
or other tools, you are asked to specify a port name on the transport switch. You can provide any port name, or accept the default, as long
as the name is unique for the switch.
The default is to set the port name to the node ID hosting the adapter at the other end of the cable.
There are no user configurable properties for cluster transport adapters of this type.
SEE ALSO
Intro(1CL), clinterconnect(1CL), clnode(1CL), scconf(1M), scinstall(1M), bge(7D)
Sun Cluster 3.2 4 May 2006 scconf_transp_adap_bge(1M)