I have an old MP-Ras Unix system. I have setup netowkring but am unable to ping any local network pcs or the default gateway. If i use the arp -a command I receive the correct mac address for all connected pcs but I cannot ping anything except the local address. Any help would be appreciative.
Last edited by DukeNuke2; 11-01-2011 at 07:34 PM..
Hi,
When I pinged a machin, I got to be seen a different kind of
reply from that machine.
This is as below : "Reply from 136.128.11.116: Source quench received." Which I felt like an un-usual message.
So what does this mean.
Regards & Thanks in advance.
Vishwa. (4 Replies)
Hi there hope list can help
I'm looking for a command that does the following
lets say i ping a server 00.00.000.00
and this server is up and running how do i get the ping command to return a UP or a Down
meaning
if the command is true do this
if the command is False do this
... (2 Replies)
We can ping out but the return never comes back even to localhost
ping localhost
PING loopback: (127.0.0.1): 56 data bytes
64 bytes from 127.0.0.1: icmp_seq=0 ttl=255 time=0 ms
it just sits there....
any ideas, any files to check (1 Reply)
Hi ,
I have one system installed on Linux Red Hat 3.0. I have ip of system 3.156.168.*** and i want to ping some port that is on this IP which command i can do this?
sam70 (1 Reply)
hi,
I m trying to ping ip on the network . The machine is started but i can't access and can't ping it .. But when i restarts that machine that works fine..... can anybody have an idea about this problem ??
if then reply ..
thanks (2 Replies)
Hi All,
Need your help one more time.
I am trying to ping a linux machine which is not responding to ping.
However traceroute can reach the machine and I can log in to it by ssh. I have checked /proc/sys/net/ipv4/icmp_echo_ignore_all it is already set as "0".
It is not happening in the... (1 Reply)
Hi,
I develop simple animation ping script on Solaris Platform. It is like Cisco ping.
Examples and source code are below.
bash-3.00$ gokcell 152.155.180.8 30
Sending 30 Ping Packets to 152.155.180.8
!!!!!!!!!!!!!.!!!!!!!!!!!!!!!.
% 93.33 success... % 6.66 packet loss...... (1 Reply)
I am unable to ping my remote server.My server is unable to ping the same. both are able to ping the gateway. both the ip's are on same network.i use a proxy tunnel on my remote server.Help if any clues. (6 Replies)
Hi
I am using perl to ping a list of nodes - with script below :
$p = Net::Ping->new("icmp");
if ($p->ping($host,1)){
print "$host is alive.\n";
}
else {
print "$host is unreacheable.\n";
}
$p->close();... (4 Replies)
help with bash script!
im am working on this script to make sure my server will stay online, so i made this script..
HOSTS="192.168.138.155"
COUNT=4
pingtest(){
for myhost in "$@"
do
ping -c "$COUNT" "$myhost" &&return 1
done
return 0
}
if pingtest $HOSTS
#100% failed... (4 Replies)
Discussion started by: mort3924
4 Replies
LEARN ABOUT FREEBSD
gre
GRE(4) BSD Kernel Interfaces Manual GRE(4)NAME
gre -- encapsulating network device
SYNOPSIS
To compile the driver into the kernel, place the following line in the kernel configuration file:
device gre
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_gre_load="YES"
DESCRIPTION
The gre network interface pseudo device encapsulates datagrams into IP. These encapsulated datagrams are routed to a destination host, where
they are decapsulated and further routed to their final destination. The ``tunnel'' appears to the inner datagrams as one hop.
gre interfaces are dynamically created and destroyed with the ifconfig(8) create and destroy subcommands.
This driver corresponds to RFC 2784. Encapsulated datagrams are prepended an outer datagram and a GRE header. The GRE header specifies the
type of the encapsulated datagram and thus allows for tunneling other protocols than IP. GRE mode is also the default tunnel mode on Cisco
routers. gre also supports Cisco WCCP protocol, both version 1 and version 2.
The gre interfaces support a number of additional parameters to the ifconfig(8):
grekey Set the GRE key used for outgoing packets. A value of 0 disables the key option.
enable_csum Enables checksum calculation for outgoing packets.
enable_seq Enables use of sequence number field in the GRE header for outgoing packets.
EXAMPLES
192.168.1.* --- Router A -------tunnel-------- Router B --- 192.168.2.*
/
/
+------ the Internet ------+
Assuming router A has the (external) IP address A and the internal address 192.168.1.1, while router B has external address B and internal
address 192.168.2.1, the following commands will configure the tunnel:
On router A:
ifconfig greN create
ifconfig greN inet 192.168.1.1 192.168.2.1
ifconfig greN inet tunnel A B
route add -net 192.168.2 -netmask 255.255.255.0 192.168.2.1
On router B:
ifconfig greN create
ifconfig greN inet 192.168.2.1 192.168.1.1
ifconfig greN inet tunnel B A
route add -net 192.168.1 -netmask 255.255.255.0 192.168.1.1
NOTES
The MTU of gre interfaces is set to 1476 by default, to match the value used by Cisco routers. This may not be an optimal value, depending
on the link between the two tunnel endpoints. It can be adjusted via ifconfig(8).
For correct operation, the gre device needs a route to the decapsulating host that does not run over the tunnel, as this would be a loop.
The kernel must be set to forward datagrams by setting the net.inet.ip.forwarding sysctl(8) variable to non-zero.
SEE ALSO gif(4), inet(4), ip(4), me(4), netintro(4), protocols(5), ifconfig(8), sysctl(8)
A description of GRE encapsulation can be found in RFC 2784 and RFC 2890.
AUTHORS
Andrey V. Elsukov <ae@FreeBSD.org>
Heiko W.Rupp <hwr@pilhuhn.de>
BUGS
The current implementation uses the key only for outgoing packets. Incoming packets with a different key or without a key will be treated as
if they would belong to this interface.
The sequence number field also used only for outgoing packets.
BSD November 7, 2014 BSD