Thanks for replies .. my problem is resolved ...
for my curiousness am asking one more question... like is there any command with terminates the sleep mode of a job.. ... is there any way to set the sleep out timings .. i means the script should sleep only for 3 hours .. if it goes beyond 3 hours it should come out of the script.
i will give u more detail
the script will sleep untill the messag becomes "P"... it may take one hour or 5 hours ... so my thing is while defining the sleep timing is there any way to give sleep time out after 3 hours .? is there any command like sleep out.
please let me know if there is such command.
Thanks
Sree
Last edited by Franklin52; 10-27-2011 at 09:07 AM..
Reason: Please use code tags, thank you
I am running a number of processes through a kill -15 loop as a temporary fix to some viscious memory leaks. I cannot pass the entire list of processes through the kill at once, because the nature of the monitoring my client has will cause the software to failover.
Because of the large number of... (1 Reply)
I am in need of some help; think I have confused myself.
Here is the issue I am faced with.
The script log file was fine, the nohup.out file has tens of thousands of lines like illegal use of sleep: sleep seconds
So I assume there is something with the seconds calculation in the script... (1 Reply)
Hi All I have a requiremnt to run a script inside another script.
here i am pulling the record count from the table in oracle.If record count is greater than 0 the script is executed.The scripts updates the count in the table and again the count is found out and the condition is checked and same... (3 Replies)
Hi Forum
Im using sleep in a while loop goes around 10 times. i feed it a variable with the time i what it to sleep for eg sleep $sleepVal and then print system date and time to screen but sometimes 1 second is added to the time why is this
here my code
sleepVal=5
while
do
... (3 Replies)
Hello,
Need a little help with the script below. I can't get it to sleep :( I'm trying to get this to check if the process is running and if it is, wait 10 secs and check again. Keep doing this until it's not running and then stop checking and send the email.
#!/bin/ksh
mailto=`cat... (2 Replies)
Hi Frnz,
I need to execute sleep command but i dont know the definite time.
Let me put my req:
I am running one shell script and this script creates some lock file in temp dir ...now in my script i want one function to go into sleep mode till this lock file exists..one lock file gone that... (6 Replies)
I need help in script.
I want my one script execute every time at 6:30 am and i have no cron access.
So i am putting sleep command there , Script may took half an hour 35 min , it depend upon queries how much it take time, but that is not issue,
So i want according to stop time of... (15 Replies)
Discussion started by: pallvi_mahajan
15 Replies
LEARN ABOUT SUNOS
sleep
sleep(1) User Commands sleep(1)NAME
sleep - suspend execution for an interval
SYNOPSIS
sleep time
DESCRIPTION
The sleep utility will suspend execution for at least the integral number of seconds specified by the time operand.
OPERANDS
The following operands are supported:
time A non-negative decimal integer specifying the number of seconds for which to suspend execution.
EXAMPLES
Example 1: Suspending command execution for a time
To execute a command after a certain amount of time:
example% (sleep 105; command)&
Example 2: Executing a command every so often
example% while true
do
command
sleep 37
done
ENVIRONMENT VARIABLES
See environ(5) for descriptions of the following environment variables that affect the execution of sleep: LANG, LC_ALL, LC_CTYPE, LC_MES-
SAGES, and NLSPATH.
EXIT STATUS
The following exit values are returned:
0 The execution was successfully suspended for at least time seconds, or a SIGALRM signal was received (see NOTES).
>0 An error has occurred.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
|Interface Stability |Standard |
+-----------------------------+-----------------------------+
SEE ALSO wait(1), alarm(2), sleep(3C), wait(3UCB), attributes(5), environ(5), standards(5)NOTES
If the sleep utility receives a SIGALRM signal, one of the following actions will be taken:
o Terminate normally with a zero exit status.
o Effectively ignore the signal.
The sleep utility will take the standard action for all other signals.
SunOS 5.10 1 Feb 1995 sleep(1)