10-26-2011
Are you running it as root?
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
I have worked with Qlogic (Sun) fiber cards a lot and with Emulex fiber cards only a little. Here is the scenario: I have a Sun 490 with 3 Emulex cards in it. A pair are for the 6120 array that is attached, the other is a direct attach so our SAN for Veritas Netbackup to back up the system.I... (0 Replies)
Discussion started by: lm_admin_dh
0 Replies
2. UNIX for Advanced & Expert Users
Hi,
I'm trying to determine which HBA cards are installed on my Solaris 10 (Sun-Fire-V240) machine.
The relevant data I have is below, but from it I cannot ascertain for sure if I have Emulex 10000 or 11000 HBA cards.
Can anyone suggest how to determine my HBA hardware ?
Thanks,
Ron.
... (3 Replies)
Discussion started by: ronbarak
3 Replies
3. Solaris
Hi,
I'm trying to determine which HBA cards are installed on my Solaris 10 (Sun-Fire-V240) machine.
The relevant data I have is below, but from it I cannot ascertain for sure if I have Emulex 10000 or 11000 HBA cards.
Can anyone suggest how to determine my HBA hardware ?
Thanks,
Ron.
... (4 Replies)
Discussion started by: ronbarak
4 Replies
4. Solaris
Hello...I got a problem here. I have HBAs installed in one of the domains in E20 and I gotta find out the brand and firmware. But when I do a prtconf, I cannot see the HBA. For other servers installed with HBAs, when I do prtconf on them I can see either qlc or em. Can you guys enlighten me how to... (5 Replies)
Discussion started by: xiaochensg
5 Replies
5. Solaris
I have installed a qlogic HBA card in an E450 Solaris 9 with all the SUNW packages and the latest EPROM version. Configuration reboot was done. An orange light flashes to the right of where the card plugs into the fiber cable after booting, and the following error apprears at the start of the boot... (9 Replies)
Discussion started by: floydm
9 Replies
6. UNIX for Advanced & Expert Users
I have a V490 that has couple internal disks attached to the same dual-port HBA card that I'm planning attach to the SAN for additional storage.
Would I sacrifice performance if I use the same HBA?
Is it better to throw in a new HBA instead? (1 Reply)
Discussion started by: kiem
1 Replies
7. AIX
Hi All,
SUN emulex HBA card has been installed on P520 box.
When i run the cfgmgr i am getting the following message.
lpar2#cfgmgr
cfgmgr: 0514-621 WARNING: The following device packages are required for
device support but are not currently installed.... (0 Replies)
Discussion started by: b_manu78
0 Replies
8. Solaris
Hi,
i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port.
---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ----------
please help :( (7 Replies)
Discussion started by: rishiraaz
7 Replies
9. Solaris
I have JNI FCE-6460-N fc card , it is detected in OK prompt.....I connected Sun StorEDGE A5000 FC storage.
in OK prompt, PROBE-SCSI-ALL
showing A5000 fc hdds details in ok prompt.....
but in OS level.....not showing the hdd, i tried in DEVFSADM command and FORMAT command not showing A5000... (3 Replies)
Discussion started by: anysystem
3 Replies
10. Red Hat
Hi,
How to determine if HBA card in getting faulty from linux host ? any pointers. (2 Replies)
Discussion started by: saurabh84g
2 Replies
PIDOF(8) Linux System Administrator's Manual PIDOF(8)
NAME
pidof -- find the process ID of a running program.
SYNOPSIS
pidof [-s] [-c] [-n] [-x] [-o omitpid[,omitpid..]] [-o omitpid[,omitpid..]..] program [program..]
DESCRIPTION
Pidof finds the process id's (pids) of the named programs. It prints those id's on the standard output. This program is on some systems
used in run-level change scripts, especially when the system has a System-V like rc structure. In that case these scripts are located in
/etc/rc?.d, where ? is the runlevel. If the system has a start-stop-daemon (8) program that should be used instead.
OPTIONS
-s Single shot - this instructs the program to only return one pid.
-c Only return process ids that are running with the same root directory. This option is ignored for non-root users, as they will be
unable to check the current root directory of processes they do not own.
-n Avoid stat(2) system function call on all binaries which are located on network based file systems like NFS. Instead of using this
option the the variable PIDOF_NETFS may be set and exported.
-x Scripts too - this causes the program to also return process id's of shells running the named scripts.
-o omitpid
Tells pidof to omit processes with that process id. The special pid %PPID can be used to name the parent process of the pidof pro-
gram, in other words the calling shell or shell script.
EXIT STATUS
0 At least one program was found with the requested name.
1 No program was found with the requested name.
NOTES
pidof is actually the same program as killall5; the program behaves according to the name under which it is called.
When pidof is invoked with a full pathname to the program it should find the pid of, it is reasonably safe. Otherwise it is possible that
it returns pids of running programs that happen to have the same name as the program you're after but are actually other programs. Note
that that the executable name of running processes is calculated with readlink(2), so symbolic links to executables will also match.
SEE ALSO
shutdown(8), init(8), halt(8), reboot(8), killall5(8)
AUTHOR
Miquel van Smoorenburg, miquels@cistron.nl
01 Sep 1998 PIDOF(8)