10-26-2011
Bundle of Thanks Vishal Aswani and solaris_1977.
9 More Discussions You Might Find Interesting
1. Solaris
Is there a way to do this in Solaris?
For instance, suppose I run the following:
$ swap -l
swapfile dev swaplo blocks free
/dev/md/dsk/d501 85,501 16 16780208 16780208
$ swap -s
total: 3377368k bytes allocated + 519416k reserved = 3896784k used, 11011992k available... (1 Reply)
Discussion started by: lyonsd
1 Replies
2. Solaris
Dear all,
I found a big problem with my solaris9 server when user said their application run too slow then I try to check cpu, memory but both of them are normally. One thing that I see form value of vmstat like this
kthr memory page disk faults ... (2 Replies)
Discussion started by: unitipon
2 Replies
3. UNIX for Dummies Questions & Answers
My unix box always experience high memory pages swapped out. This box has 8GB physical memory and the utilisation is only around 40%. What should be done to lower the memory pages swapped out problem ?
Thanks.:) (3 Replies)
Discussion started by: olive
3 Replies
4. Solaris
I'm mirroring up a T2000. Able to metainit and metattach all partitions with the exception of root. Getting the following error:
metattach: <hostname>; c1t1d0s0; is mounted on /
I'm stumped. By the way, target 1 is the boot disk. (7 Replies)
Discussion started by: Probos
7 Replies
5. Shell Programming and Scripting
Hi All,
I need to sum numbers, in bash, input is this:
10.00
12.33
14.99
134.00
1211.09
130.01- <--- it is negative, but "-" is at the end..
901.99
10.34- <--- another negative number...
bc -l is giving me error so only solution to my problem would be to swap - to the... (3 Replies)
Discussion started by: columb
3 Replies
6. Solaris
At a new job, I've inherited a handful of Solaris 10 SunFire V240 servers.
I noticed that the metadevices are not consistent, in a way that I've not seen before....
internal mirrored disks:
metadevice d60 has c1t0d0s6 as submirror 0 (d61) and c1t1d0s6 as submirror 1 (d62)
metadevice... (1 Reply)
Discussion started by: Max Power
1 Replies
7. Solaris
I recently had a vendor hot-swap a faulty hard drive on my system. The fault was determined before there were any noticeable errors with regular operation on the user end. The vendor claims to have replaced the faulty hard drive. Is there a way to verify that the hard drive has been replaced? I... (3 Replies)
Discussion started by: MaindotC
3 Replies
8. Solaris
Hi Guys,
I m not ble to perform metattaach with new disk.
Getting below Error:-
-bash-3.00$ sudo /usr/sbin/metattach d0 d10
metattach: server03: /dev/md/rdsk/d10: No such device or address
This is wht my metastat -p shows:-
-bash-3.00$ sudo /usr/sbin/metastat -p
Password:
d4 -m... (4 Replies)
Discussion started by: manalisharmabe
4 Replies
9. Shell Programming and Scripting
Hi,
I am doing aws security group auditing every day to find the difference. I am using git to find the difference. But some times some security group rules order is changing up and down(swapping lines). So 'git diff' command gives this as a difference which i dont want(i need only new lines... (2 Replies)
Discussion started by: jobycxa
2 Replies
LEARN ABOUT DEBIAN
bpecho
BPECHO(1) BP executables BPECHO(1)
NAME
bpecho - Bundle Protocol reception test program
SYNOPSIS
bpecho ownEndpointId
DESCRIPTION
bpecho uses Bundle Protocol to receive application data units from a remote bpdriver application task. In response to each received
application data unit it sends back an "echo" application data unit of length 2, the NULL-terminated string "x".
bpecho terminates upon receiving the SIGQUIT signal, i.e., ^C from the keyboard.
EXIT STATUS
0 bpecho has terminated normally. Any problems encountered during operation will be noted in the ion.log log file.
1 bpecho has terminated due to a BP reception failure. Details should be noted in the ion.log log file.
FILES
No configuration files are needed.
ENVIRONMENT
No environment variables apply.
DIAGNOSTICS
Diagnostic messages produced by bpecho are written to the ION log file ion.log.
Can't attach to BP.
bpadmin has not yet initialized Bundle Protocol operations.
Can't open own endpoint.
Another application has already opened ownEndpointId. Terminate that application and rerun.
bpecho bundle reception failed.
BP system error. Check for earlier diagnostic messages describing the cause of the error; correct problem and rerun.
No space for ZCO extent.
ION system error. Check for earlier diagnostic messages describing the cause of the error; correct problem and rerun.
Can't create ZCO.
ION system error. Check for earlier diagnostic messages describing the cause of the error; correct problem and rerun.
bpecho can't send echo bundle.
BP system error. Check for earlier diagnostic messages describing the cause of the error; correct problem and rerun.
BUGS
Report bugs to <ion-bugs@korgano.eecs.ohiou.edu>
SEE ALSO
bpadmin(1), bpdriver(1), bpcounter(1), bp(3)
perl v5.14.2 2012-05-25 BPECHO(1)