10-20-2011
It may be a boot-order problem, with disks appearing in a different order than grub used to see. It finds the boot sector on the right drive, which gets you into grub, but can't find the kernels or config file after that, being on a partition somewhere in a now-different place. Is that adjustable in the bios?
9 More Discussions You Might Find Interesting
1. Solaris
Hi,
I am a newbie to Solaris. I want to know how to find out the controller target and disk number on a SunFire V890 box that has 6X72GB disks. The probe-scsi output is as shown below:
/pci@8,600000/SUNW,qlc@2
LiD HA LUN --- Port WWN --- ----- Disk description -----
0 0 0 ... (1 Reply)
Discussion started by: sudhir_shet
1 Replies
2. SCO
hi...
i hav a problem to install sco unix
while installing sco unix 5.0.5 in acer altos with hardware raid
am getting error
"Warning HD: no root disk controller was found
system error 5: while getting fs type
flushing controller: DAC960PRL cache done."
i hav use the following... (18 Replies)
Discussion started by: mselvaprakash
18 Replies
3. HP-UX
Replace an unknown status controller on HP FC60 disk array
Author:JoyOnline JoyChangLu@gmail.com
Trouble description:
The users detected that the status of controller at A is unknown.
Analysis and diagnostic:
Physical observed all leds on enclosure of disk array is normal.
The... (4 Replies)
Discussion started by: JoyOnLine
4 Replies
4. SCO
I'm "attempting" to install SCO 5.0.7 on an HP ML370 G4 server and am ready to bash the keyboard with head now. I keep getting the error message "WARNING hd: no root disk controller found" when running the bootable install cd.
I have a raid 5 array with an online spare created using 4 36.3 GB... (2 Replies)
Discussion started by: FrictionBurn
2 Replies
5. Solaris
hi all
i am using vxvm 5.1 on my sun blade 150 which is running with solaris 5.10. When i give the command "vxdisk list" it gives the following output
# vxdisk list
DEVICE TYPE DISK GROUP STATUS
c0t0d0s2 auto:none - - online... (2 Replies)
Discussion started by: kingston
2 Replies
6. SCO
So today I tried to upgrade a customer from a Proliant with an HPSAS controller to an Intel server with a MEGASAS controller.
First, I downloaded the megasas driver from SCO and installed it on the old system.
Then I created a new Microlite Edge emergency boot cd with the new driver on it.
I... (2 Replies)
Discussion started by: jgt
2 Replies
7. Solaris
Here is my problem:
I have an 1.5TB disk with OpenSolaris (b134, b151a) using non AHCI. I then changed to AHCI in BIOS, which results in severe problems: I can not boot the system.
I suspect the problem is because I changed to AHCI. Now I have changed back to non AHCI, but still I can not... (0 Replies)
Discussion started by: kebabbert
0 Replies
8. Solaris
Hi
The scenario in the oracle t4-1 hardware with solaris 10 is as follows:
1. The initial install on the server was performed with an incorrect disk layout.
2. New disks were ordered and slot into the server.
3. The disks are allocated a controller and a disk number based on the disk or... (13 Replies)
Discussion started by: kerrygold
13 Replies
9. Linux
Hi,
a little while ago, one of the GPT Partitioned hard disk had gone faulty in a Mirror RAID and is now successfully replaced.
here is how I did that.
1) created identical partition table on the new disk.
2) attached the mirrors using md commands.
The whole procedure is given below:... (2 Replies)
Discussion started by: busyboy
2 Replies
GRUB(8) FSF GRUB(8)
NAME
grub - the grub shell
SYNOPSIS
grub [OPTION]...
DESCRIPTION
Enter the GRand Unified Bootloader command shell.
--batch
turn on batch mode for non-interactive use
--boot-drive=DRIVE
specify stage2 boot_drive [default=0x0]
--config-file=FILE
specify stage2 config_file [default=/boot/grub/menu.lst]
--device-map=FILE
use the device map file FILE
--help display this message and exit
--hold wait until a debugger will attach
--install-partition=PAR
specify stage2 install_partition [default=0x20000]
--no-config-file
do not use the config file
--no-curses
do not use curses
--no-floppy
do not probe any floppy drive
--no-pager
do not use internal pager
--preset-menu
use the preset menu
--probe-second-floppy
probe the second floppy drive
--read-only
do not write anything to devices
--verbose
print verbose messages
--version
print version information and exit
REPORTING BUGS
Report bugs to <bug-grub@gnu.org>.
SEE ALSO
update-grub(8), grub-install(8).
The full documentation for grub is maintained as a Texinfo manual in the grub-legacy-doc package. If the info and grub programs are prop-
erly installed at your site, the command
info grub
should give you access to the complete manual.
grub (GNU GRUB 0.97) January 2013 GRUB(8)