10-17-2011
Dummy check : copy/paste the output of "ifconfig eth0:1". Alternatively, run "ip addr" (but ignore this if it doesnt work)
10 More Discussions You Might Find Interesting
1. IP Networking
Hello all, I have this Intel Pentium 233/128 running Solaris 8. I also have a dhcp/router/dns running SuSElinux 7.2.(Sorry if it is out of topic here) My problem is that the Solaris box when it tries to configure the interface (elxl0) via dhcp it fails. It appears, according to the... (1 Reply)
Discussion started by: jdevarie
1 Replies
2. UNIX for Dummies Questions & Answers
When using DHCP how can I can my hostname. I vi all the hosts file and if still didn't work. So now my hostname is unknown and I want to change it. So if anyone out there can help me. Thank You (6 Replies)
Discussion started by: aojmoj
6 Replies
3. UNIX for Advanced & Expert Users
Hi you all. I'm trying to enable DHCP in a Sun Utra 5 runing Solaris 8 but during the boot process it sends me the message : "Device not in appropiate status"
Do anyone have enabled DHCP on solaris 8?
Any Procedure?
The DHCP server is an NT I guess. (2 Replies)
Discussion started by: alex blanco
2 Replies
4. UNIX for Dummies Questions & Answers
HI,
New to Unix and I inherited a network that runs DHCP in manual configuration mode. Basically, in order for a machine to get an IP it has to have an entry in dhcpd.conf with its MAC address mapped to a hostname (the hostname then maps to an IP address listed in the DNS db file). If there is... (2 Replies)
Discussion started by: NJay
2 Replies
5. UNIX for Advanced & Expert Users
Last question for today!! :rolleyes:
In what file does the DHCP server keep its list of leases?
THANKS!!! :)
Maria from Maria (2 Replies)
Discussion started by: marjeg
2 Replies
6. Solaris
Can someone help me with this please. I am new to this:
I am trying to install Solaris 8 over the network using my DHCP. After I type the comman:
./add_install_client -d -e 8:0:20:7e:97:51
I would get something like this:
cleaning up preexisting install client "8:0:20:7e:97:51"... (0 Replies)
Discussion started by: aliban83
0 Replies
7. IP Networking
can I request for an ipaddress through dhcp client by sending ipaddress as input during the invokation of dhcpclient so that it requests the server for the same,instead of depending on the configuration file . (3 Replies)
Discussion started by: Gopi Krishna P
3 Replies
8. IP Networking
Dear Experts,
I have a TI DM8148 EVM board REV C, the EZSDK5.05 SW package, and DVRRDK1.09 SW package.
EZSDK5.05, DVRRDK1.09 both use Linux2.6.37, however, there are some modifications between these two kernels.
When I use uImage of DVRRDK1.09 to boot up EVM board, this board can be given a... (0 Replies)
Discussion started by: oobin168
0 Replies
9. IP Networking
Hi All ,
please view the set up below:
-------------------------------------------------------------------
| DHCP Server |-----------| ROUTER & |-----------| Clients |
| 192.168.99.1 | - -<eth1>| DHCP-RELAY|<eth2>-- | 192.168.88.X |
... (2 Replies)
Discussion started by: gdangoor
2 Replies
10. IP Networking
I have a DHCP thing on my HP printer. How can I find information on numbers for that? (2 Replies)
Discussion started by: teak
2 Replies
LEARN ABOUT DEBIAN
pppoe-sniff
PPPOE-SNIFF(8) System Manager's Manual PPPOE-SNIFF(8)
NAME
pppoe-sniff - examine network for non-standard PPPoE frames
SYNOPSIS
pppoe-sniff [options]
DESCRIPTION
pppoe-sniff listens for likely-looking PPPoE PADR and session frames and deduces extra options required for pppoe(8) to work.
Some DSL providers seem to use non-standard frame types for PPPoE frames, and/or require a certain value in the Service-Name field. It is
often easier to sniff those values from a machine which can successfully connect rather than try to pry them out of the DSL provider.
To use pppoe-sniff, you need two computers, a DSL modem and an Ethernet hub (not an Ethernet switch.)
If the DSL modem normally connects directly to your computer's Ethernet card, connect it to the "uplink" port on the Ethernet hub. Plug
two computers into normal ports on the hub. On one computer, run whatever software the DSL provider gave you on whatever operating system
the DSL provider supports. On the other computer, run Linux and log in as root.
On the Linux machine, put the Ethernet interface into promiscuous mode and start pppoe-sniff. If the ethernet interface is eth0, for exam-
ple, type these commands:
ifconfig eth0 promisc
pppoe-sniff -I eth0
On the other machine, start your DSL connection as usual. After a short time, pppoe-sniff should print recommendations for the value of
PPPOE_EXTRA. Set this value in /etc/ppp/pppoe.conf. If pppoe-sniff indicates that something special is required in PPPOE_EXTRA, please e-
mail this to pppoe@roaringpenguin.com along with the name of your ISP and the manufacturer and model number of your DSL modem. This infor-
mation will be collated and provided on the PPPoE web page for users who do not have two computers.
After pppoe-sniff finishes (or you stop it if it seems hung), remember to turn off promiscuous mode:
ifconfig eth0 -promisc
OPTIONS
-I interface
The -I option specifies the Ethernet interface to use. Under Linux, it is typically eth0 or eth1. The interface should be "up" and
in promiscuous mode before you start pppoe-sniff.
-V The -V option causes pppoe-sniff to print its version number and exit.
BUGS
pppoe-sniff only works on Linux.
AUTHORS
pppoe-sniff was written by David F. Skoll <dfs@roaringpenguin.com>.
The pppoe home page is http://www.roaringpenguin.com/pppoe/.
SEE ALSO
pppd(8), pppoe(8), pppoe-sniff(8), pppoe-relay(8), /usr/share/doc/pppoe/README.Debian.gz
4th Berkeley Distribution 3 July 2000 PPPOE-SNIFF(8)