i want to assign new ip adress to my aix 5.3 machine which is in LPAR
Already assigned ip is 10.62.0.21 (ent0) .
New ip will be 10.50.3.6 and gateway i believe 10.50.3.1.
i use smitty tcpip to assign ip and gateway.
Both the ips are on different subnets.should i add static route. Please suggest
below is my current route table.
Routing tables
Regards
newaix
Hi.
I have HP-9000 Server running HP-UX 10.20. rECENTLY OUR network upgraded to 100mb/sec and I want to do same on the server. So, I add the second Network card (100MB). But the problem is, I can't find a way of configuring this card. How am i going to tell the server to use this 100mb card... (1 Reply)
Hi , I came across a SUN server whereby it was installed with additional ethernet card. By right in any configuration, you would probably see the onboard ports Net0,Net1 and so on should correspond to e1000g0,e1000g1...
But instead the ext PCI takes precedence in the order and the Net0 becomes... (3 Replies)
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
HI Friends
Please answer my few douts
1, Tell me how to check the NIC & Ip address details in OK promt
2, How to check correpted memory using Vmstat command
3, HOw to chekc local usr in nIS
4, How to get the newely added NIC card name?
Thanks
Waiting for ur replies (3 Replies)
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Hello,
I need to configure a second NIC on my HP UX, B.11.31 U ia64 ...if it is helpful.
I see a good thread to start on:
Configuring NIC
https://www.unix.com/hp-ux/15589-configuring-nic.html
I have started reading the man pages listed. Without having to know every last detail is there... (3 Replies)
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
LEARN ABOUT CENTOS
unbound-streamtcp
unbound-streamtcp(1) unbound unbound-streamtcp(1)NAME
unbound-streamtcp - unbound DNS lookup utility
SYNOPSIS
unbound-streamtcp [-unsh] [-f ipaddr[@port]] name type class
DESCRIPTION
unbound-streamtcp sends a DNS Query of the given type and class for the given name to the DNS server over TCP and displays the response.
If the server to query is not given using the -f option then localhost (127.0.0.1) is used. More queries can be given on one commandline,
they are resolved in sequence.
The available options are:
name This name is resolved (looked up in the DNS).
type Specify the type of data to lookup.
class Specify the class to lookup for.
-u Use UDP instead of TCP. No retries are attempted.
-n Do not wait for the answer.
-s Use SSL.
-h Print program usage.
-f ipaddr[@port]
Specify the server to send the queries to. If not specified localhost (127.0.0.1) is used.
EXAMPLES
Some examples of use.
$ unbound-streamtcp www.example.com A IN
$ unbound-streamtcp -f 192.168.1.1 www.example.com SOA IN
$ unbound-streamtcp -f 192.168.1.1@1234 153.1.168.192.in-addr.arpa. PTR IN
EXIT CODE
The unbound-streamtcp program exits with status code 1 on error, 0 on no error.
AUTHOR
This manual page was written by Tomas Hozza <thozza@redhat.com>.
NLnet Labs Mar 21, 2013 unbound-streamtcp(1)