i want to assign new ip adress to my aix 5.3 machine which is in LPAR
Already assigned ip is 10.62.0.21 (ent0) .
New ip will be 10.50.3.6 and gateway i believe 10.50.3.1.
i use smitty tcpip to assign ip and gateway.
Both the ips are on different subnets.should i add static route. Please suggest
below is my current route table.
Routing tables
Regards
newaix
Hi.
I have HP-9000 Server running HP-UX 10.20. rECENTLY OUR network upgraded to 100mb/sec and I want to do same on the server. So, I add the second Network card (100MB). But the problem is, I can't find a way of configuring this card. How am i going to tell the server to use this 100mb card... (1 Reply)
Hi , I came across a SUN server whereby it was installed with additional ethernet card. By right in any configuration, you would probably see the onboard ports Net0,Net1 and so on should correspond to e1000g0,e1000g1...
But instead the ext PCI takes precedence in the order and the Net0 becomes... (3 Replies)
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
HI Friends
Please answer my few douts
1, Tell me how to check the NIC & Ip address details in OK promt
2, How to check correpted memory using Vmstat command
3, HOw to chekc local usr in nIS
4, How to get the newely added NIC card name?
Thanks
Waiting for ur replies (3 Replies)
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Hello,
I need to configure a second NIC on my HP UX, B.11.31 U ia64 ...if it is helpful.
I see a good thread to start on:
Configuring NIC
https://www.unix.com/hp-ux/15589-configuring-nic.html
I have started reading the man pages listed. Without having to know every last detail is there... (3 Replies)
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
LEARN ABOUT DEBIAN
vde_l3
VDE_L3(1) General Commands Manual VDE_L3(1)NAME
vde_l3 - Virtual Distributed Ethernet 'Layer 3' Switch.
SYNOPSIS
vde_l3 -v vde_plug:ipaddress/netmask [-v...] [-r target_network/netmask:gateway] [-G default_gw] [-M mgmt_socket]
DESCRIPTION
A vde_l3 connects to one or more vde_switches, performing ip forwarding among its virtual interfaces. A new interface is created at startup
for each -v option given at command line. Static routes to target networks can be defined using the -r option.
vde_l3 -v /var/run/s1.ctl:192.168.0.1/24
connects to the vde sock at /var/run/s1.ctl with its virtual interface ve0, having the address 192.168.0.1 and netmask 255.255.255.0.
vde_l3
-v /var/run/s1.ctl:192.168.0.1/24
-v /var/run/s2.ctl:10.0.0.254/255.255.0.0
connects to the two vde socks, with its virtual interfaces ve0 and ve1, having addressess 192.168.1.0 and 10.0.0.254 respectively. Hosts in
each network can specify the vde_l3 as their gateway to reach the other one.
OPTIONS -v vde_plug:ipaddress/netmask
Creates a virtual network interfaces on the vde_l3 box, with address ipaddress and netmask netmask. Please note that the netmask can
be specified either in the 'classic' A.B.C.D mode, or just by giving the number of leading bits (f.e., /17 for 255.255.128.0). One
can define as many interfaces as she wants.
-r target_network/netmask:gateway
Specify a static route through gateway to reach hosts in target_network with netmask netmask. One can define as many routes as she
wants.
-G default_gw
Specify a default gateway, to be used whenever no static route is defined for a target host.
-M mgmt_socket
the unix socket where the parameters (interfaces addresses, routes, etc.) can be checked and changed runtime. unixterm(1) can be
used as a remote terminal for wirefilter.
NOTICE
Virtual Distributed Ethernet is not related in any way with www.vde.com ("Verband der Elektrotechnik, Elektronik und Informationstechnik"
i.e. the German "Association for Electrical, Electronic & Information Technologies").
SEE ALSO vde_switch(1), vdeq(1), unixterm(1), vde_cryptcab(1), wirefilter(1).
AUTHORS
VDE_L3 is a tool by Daniele Lacamera <root@danielinux.net>
VDE is a project by Renzo Davoli <renzo@cs.unibo.it>
Virtual Distributed Ethernet May 7, 2007 VDE_L3(1)