10-09-2011
According to the SCO hardware list, there are no PCIExpress cards that support parallel SCSI disk drives, for release 5.0.7 or 6.0.0
10 More Discussions You Might Find Interesting
1. Solaris
How do I get the PCI ID for my Realtek adapter?
It's a Solaris x86 installation. (5 Replies)
Discussion started by: kuultak
5 Replies
2. Solaris
Has anyone ever relocated an HBA card after already having it configured in another PCI slot? I've found that the HBA instance #'s start incrementing past the previous. It results in me having to have my instance numbers in /kernel/drv/qla2300.conf be 4,5,6,7 instead of 0,1,2,3. Cleanup with... (5 Replies)
Discussion started by: kduffin
5 Replies
3. AIX
I have 1 PCI-X Dual Channel Ultra320 SCSI Adapter card for my p570 server. I would like to split the 2 channels for the usage of 2 tape drives in different LPARs. Is that possible?
For example, I have 2 LPARs running in p570 server, LPAR-A configured the Ultra320 card as pci7 in slot... (11 Replies)
Discussion started by: kwliew999
11 Replies
4. SCO
I'm floundering here trying to locate a PCI-E 1x HBA that will support an external tape drive in SCO Openserver 6. I was unable to find anything that would work in the compatible hardware list and a call to Adaptec confirmed that PCI-X would've been a better option for the risers in the Dell 2950... (1 Reply)
Discussion started by: s_mal
1 Replies
5. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
6. SCO
OK group, it's been 12 years since I worked with SCO. I need some direction here:
SCO Openserver 5.07
I have a server with a bad motherboard. I have moved the SCSI adapter and hard drive to another computer. This new server has different hardware so I must install the chipset drivers for... (1 Reply)
Discussion started by: jscholz
1 Replies
7. Hardware
Internally speaking, for your motherboard bus. Would it be possible for a usb standard to be used in place of the PCI or PCIe bus that is now nearly standard on all PC's? If not, why wouldn't this work? (8 Replies)
Discussion started by: Lost in Cyberia
8 Replies
8. Red Hat
I am trying to cause a callback in the Linux nvme driver by using AER injection. I've modified the AER source code to directly inject errors through module loading rather than from userland program.
I've verified that I got the correct bus, dev, and fn and that the error injection went... (0 Replies)
Discussion started by: Decrypto
0 Replies
9. HP-UX
I am trying to reload a RP4440 with 2x300gb disks and dual Port Network card, with HPUX 11.11 Sept 2003. When the os boots and and gets to the main menu to install HPUX or run recovery, it cannot find the disks or NIC.
At the OS prompt (after loading files), ioscan shows the Class ba, and shows... (0 Replies)
Discussion started by: mrmurdock
0 Replies
10. Solaris
Hi,
I have a Sun Fire V440 server that fails to boot up correctly. A lot of services are not started and the sytems acts really slow to commands. During boot I can see the following Error:
WARNING: /pci@1f,700000/scsi@2/sd@0,0 (sd1):
SCSI transport failed: reason 'reset': retrying... (15 Replies)
Discussion started by: oliwei
15 Replies
VPO(4) BSD Kernel Interfaces Manual VPO(4)
NAME
vpo -- parallel to SCSI interface driver
SYNOPSIS
device vpo
For one or more SCSI busses:
device scbus
DESCRIPTION
The vpo driver provide access to parallel port Iomega Zip and Jaz drives.
HARDWARE
The vpo driver supports the following parallel to SCSI interfaces:
o Adaptec AIC-7110 Parallel to SCSI interface (built-in to Iomega ZIP drives)
o Iomega Jaz Traveller interface
o Iomega MatchMaker SCSI interface (built-in to Iomega ZIP+ drives)
USAGE
The driver should let you use a printer connected to the drive while transferring data.
DOS and FreeBSD file systems are supported. When mounting a DOS file system or formating a FreeBSD file system, check the slice of the disk
with the fdisk(8) utility.
In order to unixify a ZIP disk, put the following in /etc/disktab:
zip|zip 100:
:ty=removable:se#512:nc#96:nt#64:ns#32:
:pa#196608:oa#0:ba#4096:fa#512:
:pb#196608:ob#0:bb#4096:fb#512:
:pc#196608:oc#0:bc#4096:fc#512:
and use bsdlabel(8).
If you have trouble with your driver, your parallel chipset may not run properly at the detected mode (NIBBLE, PS2 or EPP). Tune the ppc(4)
bootflags to force other modes.
SEE ALSO
da(4), lpt(4), ppbus(4), ppc(4), scsi(4)
HISTORY
The vpo manual page first appeared in FreeBSD 3.0.
AUTHORS
This manual page was written by Nicolas Souchu.
BUGS
During boot, the driver first tries to detect a classic ZIP, then a ZIP+. The ZIP+ detection is intrusive and may send erroneous characters
to your printer if the drive is not connected to your parallel port.
BSD
December 14, 2004 BSD