10-06-2011
thanx Hartz, sorry for late reply...
I've tried the
last | grep 192.xxxxx
but the result was nothing.
and ifconfig -a to look just for local IP, not all existing IP on my network? like 192.168.1.1; 192.168.1.2; 192.168.1.3.....etc
cmiiw
the problem is, I have a server that its name xxx.lan (example), and I usually access from Windows
start-run \ \ xxx, and now... forget what its IP
now, can i know the IP xxx, and anyone who access that server? and also the Log?
many thnx
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hey,
Just need a little help I'm not sure wat I should do.
We have several little networks setup for testing different things. One of these networks we need to have running at full dulpex.
Right now we run 2 hubs (to go off to 2 differnt parts) and they are half dulpex hubs.
Is is... (1 Reply)
Discussion started by: merlin
1 Replies
2. Linux
I have setup a AS 2.1 server with no X running or installed. I need to know how to configure the IP and such from command line and change it from DHCP. We used DHCP at first since we didn't know the IP we were going to use and now I need to change it. Any help would be great as Redhat's site just... (2 Replies)
Discussion started by: Acleoma
2 Replies
3. Solaris
I have a machine that has developed a strange network problem. Anytime it sends an FTP file somewherwe, no problem. When it is the target machine, extremely slow. I checked the /var/adm/messages file and found a few of these:
SUNW,hme0 : No response from Ethernet network : Link down -- cable... (2 Replies)
Discussion started by: hshapiro
2 Replies
4. UNIX for Dummies Questions & Answers
This is my first attempt in installing a netbsd ever. I'm trying to get myself familiar with some commands and how things work in unix and so far i never knew its this fun. Anyway, unix is our elective here in school and school is gonna start 2 weeks. I'm just trying to get a headstart on this :D... (2 Replies)
Discussion started by: 3rr0r_3rr0r
2 Replies
5. UNIX for Dummies Questions & Answers
1) how do i know my NIC speed if its 10//100???
2)how do i setup by NIC to full duplex
3) any help on setting up etherchannel for NIC failover (1 Reply)
Discussion started by: karthikosu
1 Replies
6. Solaris
I am new to Solaris and have been searching around for this answer and I think I figured it out but I wanted to run it by you folks. I was trying to figure out if the network on this Solaris 10 machine was set up for 100 Full Duplex. I think from this output that it is 100 full duplex, am I... (2 Replies)
Discussion started by: scotbuff
2 Replies
7. UNIX for Dummies Questions & Answers
Hi,
I have a linux machine connected to 2 networks, with devices eth0 and eth1.
When I give the command host whatever, how do I now which network is searched for the DNS's ? Is there a default ethernet device for network related commands ? How do I change it ? :confused: (2 Replies)
Discussion started by: mik
2 Replies
8. IP Networking
Hi here is my question;
any help would be appreciated
The Linux system pokey has two Ethernet cards. The first Ethernet card is connected to a companywide
TCP/IP network covering the addresses 87.65.43.xx, where pokey's address is
87.65.43.21. The second Ethernet interface is connected to a... (2 Replies)
Discussion started by: scofiled83
2 Replies
9. IP Networking
Folks;
I have 2 SUSE servers similar in all configuration & both on the same network
(192.168.151.10 & 192.168.151.11) with the same default gateway of 192.168.151.1 and the same netmask of 255.255.255.0 and the same firewall configuration
the first one works fine and i can ssh to it & i can... (3 Replies)
Discussion started by: Katkota
3 Replies
10. UNIX for Dummies Questions & Answers
Hi,
I am on Redhat 5. on the /etc/sysconfig/network file
I don't see GATEWAY as one line. I also checked /etc/sysconfig/network-scripts/ifcfg-eth0. I don't see GATEWAY.
But on the server. But when I do netstat -rn. I see many address. Is there some other settings ?
... (2 Replies)
Discussion started by: samnyc
2 Replies
LEARN ABOUT DEBIAN
oidentd_masq.conf
oidentd_masq.conf(5) File Formats Manual oidentd_masq.conf(5)
NAME
oidentd_masq.conf - oidentd IP masquerading/NAT configuration file.
DESCRIPTION
If you are using IP masquerading or NAT, oidentd can optionally return a username for connections from other machines. Support for this is
specified by calling oidentd with the -m (or --masq) flag and by creating an /etc/oidentd_masq.conf file.
oidentd can also forward requests for an IP masqueraded connection to the machine from which connection originates by way of the -f option.
This will only work if the host to which the connection is forwarded is running oidentd with the -P (proxy) flag, or if the host's ident
daemon will return a valid reply regardless of the input supplied by and the address of the host requesting the info (some ident daemons
for windows do this, maybe others).
FORMAT
<IP Address|Hostname>[/<Mask>] <Ident Response> <System Type>
The first field contains the IP address or the hostname of a machine that IP masquerades through the machine on which oidentd runs. The
mask parameter can be either a network mask or a mask in CIDR notation. A mask of 24 is equivalent to 255.255.255.0, a mask of 16 is
equivalent to 255.255.0.0, etc.
The second field specifies the reply that oidentd will return for lookups to the host matching the IP address specified in the first param-
eter.
The third field specifies the operating system the machine matching the first parameter is running.
EXAMPLES
<Host>[/<Mask>] <Ident Response> <System Type>
192.168.1.1 someone UNIX
192.168.1.2 noone WINDOWS
192.168.1.1/32 user1 UNIX
192.168.1.0/24 user3 UNIX
192.168.0.0/16 user4 UNIX
somehost user5 UNIX
192.168.1.0/255.255.255.0 user6 UNIX
AUTHOR
Ryan McCabe <ryan@numb.org>
http://dev.ojnk.net
SEE ALSO
oidentd(8) oidentd.conf(5)
version 2.0.8 13 Jul 2003 oidentd_masq.conf(5)