10-06-2011
thanx Hartz, sorry for late reply...
I've tried the
last | grep 192.xxxxx
but the result was nothing.
and ifconfig -a to look just for local IP, not all existing IP on my network? like 192.168.1.1; 192.168.1.2; 192.168.1.3.....etc
cmiiw
the problem is, I have a server that its name xxx.lan (example), and I usually access from Windows
start-run \ \ xxx, and now... forget what its IP
now, can i know the IP xxx, and anyone who access that server? and also the Log?
many thnx
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hey,
Just need a little help I'm not sure wat I should do.
We have several little networks setup for testing different things. One of these networks we need to have running at full dulpex.
Right now we run 2 hubs (to go off to 2 differnt parts) and they are half dulpex hubs.
Is is... (1 Reply)
Discussion started by: merlin
1 Replies
2. Linux
I have setup a AS 2.1 server with no X running or installed. I need to know how to configure the IP and such from command line and change it from DHCP. We used DHCP at first since we didn't know the IP we were going to use and now I need to change it. Any help would be great as Redhat's site just... (2 Replies)
Discussion started by: Acleoma
2 Replies
3. Solaris
I have a machine that has developed a strange network problem. Anytime it sends an FTP file somewherwe, no problem. When it is the target machine, extremely slow. I checked the /var/adm/messages file and found a few of these:
SUNW,hme0 : No response from Ethernet network : Link down -- cable... (2 Replies)
Discussion started by: hshapiro
2 Replies
4. UNIX for Dummies Questions & Answers
This is my first attempt in installing a netbsd ever. I'm trying to get myself familiar with some commands and how things work in unix and so far i never knew its this fun. Anyway, unix is our elective here in school and school is gonna start 2 weeks. I'm just trying to get a headstart on this :D... (2 Replies)
Discussion started by: 3rr0r_3rr0r
2 Replies
5. UNIX for Dummies Questions & Answers
1) how do i know my NIC speed if its 10//100???
2)how do i setup by NIC to full duplex
3) any help on setting up etherchannel for NIC failover (1 Reply)
Discussion started by: karthikosu
1 Replies
6. Solaris
I am new to Solaris and have been searching around for this answer and I think I figured it out but I wanted to run it by you folks. I was trying to figure out if the network on this Solaris 10 machine was set up for 100 Full Duplex. I think from this output that it is 100 full duplex, am I... (2 Replies)
Discussion started by: scotbuff
2 Replies
7. UNIX for Dummies Questions & Answers
Hi,
I have a linux machine connected to 2 networks, with devices eth0 and eth1.
When I give the command host whatever, how do I now which network is searched for the DNS's ? Is there a default ethernet device for network related commands ? How do I change it ? :confused: (2 Replies)
Discussion started by: mik
2 Replies
8. IP Networking
Hi here is my question;
any help would be appreciated
The Linux system pokey has two Ethernet cards. The first Ethernet card is connected to a companywide
TCP/IP network covering the addresses 87.65.43.xx, where pokey's address is
87.65.43.21. The second Ethernet interface is connected to a... (2 Replies)
Discussion started by: scofiled83
2 Replies
9. IP Networking
Folks;
I have 2 SUSE servers similar in all configuration & both on the same network
(192.168.151.10 & 192.168.151.11) with the same default gateway of 192.168.151.1 and the same netmask of 255.255.255.0 and the same firewall configuration
the first one works fine and i can ssh to it & i can... (3 Replies)
Discussion started by: Katkota
3 Replies
10. UNIX for Dummies Questions & Answers
Hi,
I am on Redhat 5. on the /etc/sysconfig/network file
I don't see GATEWAY as one line. I also checked /etc/sysconfig/network-scripts/ifcfg-eth0. I don't see GATEWAY.
But on the server. But when I do netstat -rn. I see many address. Is there some other settings ?
... (2 Replies)
Discussion started by: samnyc
2 Replies
LEARN ABOUT DEBIAN
linux-version
LINUX-VERSION(1) General Commands Manual LINUX-VERSION(1)
NAME
linux-version - operate on Linux kernel version strings
SYNOPSIS
linux-version compare VERSION1 OP VERSION2
linux-version sort [--reverse] [VERSION1 VERSION2 ...]
linux-version list [--paths]
DESCRIPTION
linux-version operates on Linux kernel version strings as reported by uname -r and used in file and directory names. These version strings
do not follow the same rules as Debian package version strings and should not be compared as such or as arbitrary strings.
compare VERSION1 OP VERSION2
Compare version strings, where OP is a binary operator. linux-version returns success (zero result) if the specified condition is
satisfied, and failure (nonzero result) otherwise. The valid operators are: lt le eq ne ge gt
sort [--reverse] [VERSION1 VERSION2 ...]
Sort the given version strings and print them in order from lowest to highest. If the --reverse option is used, print them in order
from highest to lowest.
If no version strings are given as arguments, the version strings will instead be read from standard input, one per line. They may
be suffixed by arbitrary text after a space, which will be included in the output. This means that, for example:
linux-version list --paths | linux-version sort --reverse
will list the installed versions and corresponding paths in order from highest to lowest version.
list [--paths]
List kernel versions installed in the customary location. If the --paths option, show the corresponding path for each version.
AUTHOR
linux-version and this manual page were written by Ben Hutchings as part of the Debian linux-base package.
30 March 2011 LINUX-VERSION(1)