prtdiag -v problem :Memory Module Groups status not Showing
Hi Friends,
I need a help from you all.
In my machine which is on Solaris 9.
the command
Code:
prtdiag -v
shows the complete output but it doesn't show "Memory Module Groups status" status.
I have tried restarting the picl daemon, but still it doesn't work.
hi,
we have an e6900 and my sys admin says that the number of processors and memory were reduced to 4 and 8GB. However, a prtdiag |grep Memory returns 16GB of memory. So what is my system's memory? psrinfo returns 4 online and 4 offline CPUs.
Thanks.
Kumar (1 Reply)
Hi, a couple of T2000 servers did not show the component status and the output was too short. There was a patch that needed to be installed. I also updated to the latest recommended patch cluster and OBP patch.
After reboot/restart of picl, it worked ok for a couple of weeks. Then suddenly it went... (12 Replies)
Hi,
Recently one of my server V490 showed memory issues on
"Fault_PC 0x10158dec Esynd 0x01e2 Slot A: J3001"
Below is the prtdiag info
========================= Memory Configuration ===============================
Logical Logical Logical
MC Bank Bank Bank ... (6 Replies)
Hi. I have 2 SunFire V490 servers running Solaris 10. We may have to upgrade with more memory on one of them to make it compatible with the other. Here's the one with 12GB of RAM:
Memory size: 12288 Megabytes
========================= CPUs ===============================================
... (1 Reply)
Hi Experts
I am getting following status
# svcs wbem
STATE STIME FMRI
online* 18:19:29 svc:/application/management/wbem:default
/var/svc/log/application-management-wbem:default.log is being flooded with following message (5 Replies)
hi all
we recently upgraded our san switches. after that, i found i got many hdisks showing in lsdev with status "Defined" and "Available". the number of "Defined" is equal to "Available". the time stamp shows all "Available" disks created at our downtime night.
"datapath query device"... (0 Replies)
Hi All,
I am using HP-UX 11i v1(B11.11) servers for my work and its memory (RAM) utilization is consistenly 80% for the last one year. Though I am not facing any issues with this high memory utilization I just want to know the below queries:
1) Is it the default behavior of HP-UX systems?
2)... (20 Replies)
hello,
I did some investigation before posting.
i noticed that during the time when the httpd consumed 100% memory, only few swap was used.
i got a link on StackOverflow that says its normal as unused memory is wasted memory on Linux.
please let me have your views on this.
ps: I... (2 Replies)
So we have a RHEL 7.6 workstation with 128 gigs of ram. The OS sees all the ram and 80 cors (40 HT)
We have 1 guest with 8 CPUs and 32gigs of ram running RHEL 7.6 workstation as well. We are trying to create another guest with 64 CPUs and 80 gigs of ram. We setup the system using... (0 Replies)
Discussion started by: joeg1484
0 Replies
LEARN ABOUT DEBIAN
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)