I have a flat file and need to count no of records in the file less the header and the trailer record.
I would appreciate any and all asistance
Thanks
Hadi Lalani (2 Replies)
Situation:
Our system currently executes a job (COBOL Program) that generates an interface file to be sent to one of our vendors. Because this system processes information for over 100,000 employees/retirees (and growing), we'd like to multi-thread the job into processing-groups in order to... (4 Replies)
Hi All,
I am karthik. I am new to this forum. I have one requirement.
I have a file with header and footer.
Header may be like
HDR0001
or
FILE20090110
(Assume it is unknown so far, but i am sure there is a header in the file)
likewise file has the trailer too.
I just... (7 Replies)
Hi All,
In my file i need to remove header and trailer records which comes in 1st line and last line respectively. After that i need to replace '$\|' with '$#@'.
I am using sed command for this and its taking lot of time. Is there any other command which can be used to improve performance?
... (1 Reply)
Hi,
I want to add the below Header to all the files in sequence File1,File2,File3...etc
"ABC,<number of chracter in the file>"
e,g - If File1 is as below
pqrstuvdt
abcdefgh
then I want to add the above header into it ,So that File1 becomes as below
ABC,17
pqrstuvdt
abcdefgh
... (9 Replies)
for example, i have a file with below content:
123413
866688
816866
818818
i want the output as:
This is header
123413
866688
816866
818818
This is trailer
i am able to achieve it using a bash script. (2 Replies)
Hi,
I need a script that validates a file header/detail/trailer. File layout is:
Header - Rec_Type|File_name|File_Date
Detail - Rec_Type|field1|field2|field3...
Trailder - Rec_Type|File_name|File_Date|Record_count
Sample Data:
HDR|customer_data.dat|20120709... (7 Replies)
I need to split the file based on pattern from position 34-37 while retaining the header and trailer records in each individual split file
Also is it possible to output the TOM and PAT records in the same output file ?
I need the output file names same as xyz_pattern_Datetimestamp.txt
... (23 Replies)
I have a EBCDIC multi layout file which has a header record which is 21 bytes, The Detail records are 2427 bytes long and the trailer record is 9 bytes long.
Is there a command to remove the header as well as trailer record and read only the detail records while at the same time not altering... (1 Reply)
Discussion started by: abhilashnair
1 Replies
LEARN ABOUT OSX
cat
CAT(1) BSD General Commands Manual CAT(1)NAME
cat -- concatenate and print files
SYNOPSIS
cat [-benstuv] [file ...]
DESCRIPTION
The cat utility reads files sequentially, writing them to the standard output. The file operands are processed in command-line order. If
file is a single dash ('-') or absent, cat reads from the standard input. If file is a UNIX domain socket, cat connects to it and then reads
it until EOF. This complements the UNIX domain binding capability available in inetd(8).
The options are as follows:
-b Number the non-blank output lines, starting at 1.
-e Display non-printing characters (see the -v option), and display a dollar sign ('$') at the end of each line.
-n Number the output lines, starting at 1.
-s Squeeze multiple adjacent empty lines, causing the output to be single spaced.
-t Display non-printing characters (see the -v option), and display tab characters as '^I'.
-u Disable output buffering.
-v Display non-printing characters so they are visible. Control characters print as '^X' for control-X; the delete character (octal
0177) prints as '^?'. Non-ASCII characters (with the high bit set) are printed as 'M-' (for meta) followed by the character for the
low 7 bits.
EXIT STATUS
The cat utility exits 0 on success, and >0 if an error occurs.
EXAMPLES
The command:
cat file1
will print the contents of file1 to the standard output.
The command:
cat file1 file2 > file3
will sequentially print the contents of file1 and file2 to the file file3, truncating file3 if it already exists. See the manual page for
your shell (i.e., sh(1)) for more information on redirection.
The command:
cat file1 - file2 - file3
will print the contents of file1, print data it receives from the standard input until it receives an EOF ('^D') character, print the con-
tents of file2, read and output contents of the standard input again, then finally output the contents of file3. Note that if the standard
input referred to a file, the second dash on the command-line would have no effect, since the entire contents of the file would have already
been read and printed by cat when it encountered the first '-' operand.
SEE ALSO head(1), more(1), pr(1), sh(1), tail(1), vis(1), zcat(1), setbuf(3)
Rob Pike, "UNIX Style, or cat -v Considered Harmful", USENIX Summer Conference Proceedings, 1983.
STANDARDS
The cat utility is compliant with the IEEE Std 1003.2-1992 (``POSIX.2'') specification.
The flags [-benstv] are extensions to the specification.
HISTORY
A cat utility appeared in Version 1 AT&T UNIX. Dennis Ritchie designed and wrote the first man page. It appears to have been cat(1).
BUGS
Because of the shell language mechanism used to perform output redirection, the command ``cat file1 file2 > file1'' will cause the original
data in file1 to be destroyed!
The cat utility does not recognize multibyte characters when the -t or -v option is in effect.
BSD March 21, 2004 BSD