I have a flat file and need to count no of records in the file less the header and the trailer record.
I would appreciate any and all asistance
Thanks
Hadi Lalani (2 Replies)
Situation:
Our system currently executes a job (COBOL Program) that generates an interface file to be sent to one of our vendors. Because this system processes information for over 100,000 employees/retirees (and growing), we'd like to multi-thread the job into processing-groups in order to... (4 Replies)
Hi All,
I am karthik. I am new to this forum. I have one requirement.
I have a file with header and footer.
Header may be like
HDR0001
or
FILE20090110
(Assume it is unknown so far, but i am sure there is a header in the file)
likewise file has the trailer too.
I just... (7 Replies)
Hi All,
In my file i need to remove header and trailer records which comes in 1st line and last line respectively. After that i need to replace '$\|' with '$#@'.
I am using sed command for this and its taking lot of time. Is there any other command which can be used to improve performance?
... (1 Reply)
Hi,
I want to add the below Header to all the files in sequence File1,File2,File3...etc
"ABC,<number of chracter in the file>"
e,g - If File1 is as below
pqrstuvdt
abcdefgh
then I want to add the above header into it ,So that File1 becomes as below
ABC,17
pqrstuvdt
abcdefgh
... (9 Replies)
for example, i have a file with below content:
123413
866688
816866
818818
i want the output as:
This is header
123413
866688
816866
818818
This is trailer
i am able to achieve it using a bash script. (2 Replies)
Hi,
I need a script that validates a file header/detail/trailer. File layout is:
Header - Rec_Type|File_name|File_Date
Detail - Rec_Type|field1|field2|field3...
Trailder - Rec_Type|File_name|File_Date|Record_count
Sample Data:
HDR|customer_data.dat|20120709... (7 Replies)
I need to split the file based on pattern from position 34-37 while retaining the header and trailer records in each individual split file
Also is it possible to output the TOM and PAT records in the same output file ?
I need the output file names same as xyz_pattern_Datetimestamp.txt
... (23 Replies)
I have a EBCDIC multi layout file which has a header record which is 21 bytes, The Detail records are 2427 bytes long and the trailer record is 9 bytes long.
Is there a command to remove the header as well as trailer record and read only the detail records while at the same time not altering... (1 Reply)
Discussion started by: abhilashnair
1 Replies
LEARN ABOUT BSD
diff3
DIFF3(1) General Commands Manual DIFF3(1)NAME
diff3 - 3-way differential file comparison
SYNOPSIS
diff3 [ -exEX3 ] file1 file2 file3
DESCRIPTION
Diff3 compares three versions of a file, and publishes disagreeing ranges of text flagged with these codes:
==== all three files differ
====1 file1 is different
====2 file2 is different
====3 file3 is different
The type of change suffered in converting a given range of a given file to some other is indicated in one of these ways:
f : n1 a Text is to be appended after line number n1 in file f, where f = 1, 2, or 3.
f : n1 , n2 c Text is to be changed in the range line n1 to line n2. If n1 = n2, the range may be abbreviated to n1.
The original contents of the range follows immediately after a c indication. When the contents of two files are identical, the contents of
the lower-numbered file is suppressed.
Under the -e option, diff3 publishes a script for the editor ed that will incorporate into file1 all changes between file2 and file3, i.e.
the changes that normally would be flagged ==== and ====3. Option -x (-3) produces a script to incorporate only changes flagged ====
(====3). The following command will apply the resulting script to `file1'.
(cat script; echo '1,$p') | ed - file1
The -E and -X are similar to -e and -x, respectively, but treat overlapping changes (i.e., changes that would be flagged with ==== in the
normal listing) differently. The overlapping lines from both files will be inserted by the edit script, bracketed by "<<<<<<" and ">>>>>>"
lines.
For example, suppose lines 7-8 are changed in both file1 and file2. Applying the edit script generated by the command
"diff3 -E file1 file2 file3"
to file1 results in the file:
lines 1-6
of file1
<<<<<<< file1
lines 7-8
of file1
=======
lines 7-8
of file3
>>>>>>> file3
rest of file1
The -E option is used by RCS merge(1) to insure that overlapping changes in the merged files are preserved and brought to someone's atten-
tion.
FILES
/tmp/d3?????
/usr/libexec/diff3
SEE ALSO diff(1)BUGS
Text lines that consist of a single `.' will defeat -e.
7th Edition October 21, 1996 DIFF3(1)