09-18-2011
What do you mean by "I could not able to make work"? That you don't have a network connection? That the card wasn't configured? Or that Linux doesn't see it?
Could you post the outout of /sbin/ifconfig -a?
This User Gave Thanks to pludi For This Post:
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have installed in the server a quad ethernet adapter, I'm using two interfaces with two different IP networks, both interfaces are connected to a switch, the switch report that is receiving the same MAC address in both ports so must of the times I have connectivity problems.
Any idea to change... (1 Reply)
Discussion started by: mono673
1 Replies
2. Solaris
I have a Dual Boot system - XP with Solaris 10. I built the system from the ground up with different components and the Ethernet Card built into the Motherboard is a Marvell Yukon Gigabit Ethernet 10/100/1000 T-base, RJ-45 Copper.
I am unable to go to the Web as the Ethernet Card is still not... (2 Replies)
Discussion started by: tubbyrana
2 Replies
3. Solaris
hi all,
How to install onboard ethernet card on Sun SPARC M4000 server? (3 Replies)
Discussion started by: Tlg13team
3 Replies
4. AIX
Hi,
In our AIX 5.2 server , we have one unused ethernet adapter which doesn't have cable connection . For this interface , we are getting alerts in errpt .
Could you suggesthow to stop this alert ? And sametime i would like to keep this device in ODM .
Is there... (1 Reply)
Discussion started by: sekarsamy
1 Replies
5. AIX
All
I am trying allocate an IVE to an LPAR (not a VIO) running AIX 7.1. I am getting the error:
HSCL068A
Explanation
Logical port can not be assigned to Logical Partition because this Logical Partition is not the promiscuous LPAR for the physical port.
Has anyone encountered this... (1 Reply)
Discussion started by: johnf
1 Replies
6. Hardware
Hi,
Does anybody have a "Sun 10-Gigabit Ethernet Adapter installation CD" or driver ixge for Sun 10-Gigabit Ethernet PCI-X adapter? I need it but can't find it anywhere. So if you know where I can download it or purchase it, please let me know. (Already tried Oracle's website, don't have it) ... (5 Replies)
Discussion started by: Lhao
5 Replies
7. AIX
Hi Techies,
I have a doubt.
ent0 Available Logical Host Ethernet Port (lp-hea)
ent1 Available Logical Host Ethernet Port (lp-hea)
ent2 Available Logical Host Ethernet Port (lp-hea)
ent3 Available Logical Host Ethernet Port (lp-hea)
ent4 Available... (4 Replies)
Discussion started by: jayadeava
4 Replies
8. Solaris
Hi Community,
i have one issue with 10 fiber ethernet adapter.
here is my details:
root@new-bpel.example.com #dladm show-dev
bge0 link: unknown speed: 0 Mbps duplex: unknown
bge1 link: up speed: 1000 Mbps duplex: full
qlge2 link:... (4 Replies)
Discussion started by: bentech4u
4 Replies
9. Red Hat
Hello community, I have a Proliant HP DL380P with the following network adapters:
NetXtreme BCM5719 Gigabit Ethernet PCIe (Ethernet 1Gb 4-port 331FLR Adapter)
82580 Gigabit Network Connection (NC365T 4-port Ethernet Server Adapter)
I installed Red Hat 7.2 but it recognizes only the... (9 Replies)
Discussion started by: Lord Spectre
9 Replies
10. AIX
Hi,
We had a hardware problem with an IBM System p5 server, with AIX 5.2
We restore from a tape the last backup we had, but the server does not boot up as expected.
The server try to mount some directories from a storage, but could not comunicate with them, we check the FC and everything is... (12 Replies)
Discussion started by: trevian3969
12 Replies
LO(4) BSD Kernel Interfaces Manual LO(4)
NAME
lo -- software loopback network interface
SYNOPSIS
pseudo-device loop
DESCRIPTION
The loop interface is a software loopback mechanism which may be used for performance analysis, software testing, and/or local communication.
As with other network interfaces, the loopback interface must have network addresses assigned for each address family with which it is to be
used. These addresses may be set or changed with the SIOCSIFADDR ioctl(2). The loopback interface should be the last interface configured,
as protocols may use the order of configuration as an indication of priority. The loopback should never be configured first unless no hard-
ware interfaces exist.
The loopback interface lo0 is created at boottime, it always exists and cannot be destroyed with ifconfig(8). Additional loopback interfaces
can be created by using the ifconfig(8) create command.
DIAGNOSTICS
lo%d: can't handle af%d . The interface was handed a message with addresses formatted in an unsuitable address family; the packet was
dropped.
SEE ALSO
inet(4), intro(4), ifconfig(8)
HISTORY
The lo device appeared in 4.2BSD.
BUGS
Previous versions of the system enabled the loopback interface automatically, using a nonstandard Internet address (127.1). Use of that
address is now discouraged; a reserved host address for the local network should be used instead.
BSD
September 3, 2006 BSD