Does anyone know how to force these rogue logical volumes to mirror to there respective disks?
DISK:Logical Volumes
03:cw_p05,cw_p01_01,cw_p01_02,lv00
09:cw_p05,cw_p01_01,cw_p01_02
04:cw_p01_phyldbs,cw_p01_03,cw_op01_01,cw_od01
10:cw_p01_phyldbs,cw_p01_03,cw_op01_01 (1 Reply)
I hope I am posting in the correct forum.
I have a server - which I am installing solaris 9 on.
The server currently has 2 disks. I wish to run solaris 9 on one, and use the other as a mirror for the first one. ie. If the first one should ever fail, then I can swap to the mirror and just... (18 Replies)
I've looked a little but haven't found a solid answer, assuming there is one.
What's better, hardware mirroring or ZFS mirroring? Common practice for us was to use the raid controllers on the Sun x86 servers. Now we've been using ZFS mirroring since U6. Any performance difference? Any other... (3 Replies)
Hi ,
I am new to SVM .when i try to learn RAID 1 , first they are creating two RAID 0 strips through
metainit d51 1 1 c0t0d0s2
metainit d52 1 1 c1t0d0s2
In the next step
metainit d50 -m d51
d50: Mirror is setup
next step is
metaattach d50 d52
d50 : submirror d52 is... (7 Replies)
Hi guys,
We had created a pool as follows:
zpool create filing_pool raidz c1t2d0 c1t3d0 ........
Due to some requirement, we need to destroy the pool and re-create another one. We wish to know now which disks have been included in the filing_pool, how do we list the disks used to create... (2 Replies)
i have this pool1 on my sun4u sparc machine
bash-3.00# zpool get all pool1
NAME PROPERTY VALUE SOURCE
pool1 size 292G -
pool1 used 76.5K -
pool1 available 292G -
pool1 capacity 0% -... (1 Reply)
I have to do patching in single user mode in solaris 10 zfs root pool. Before that I have to detach the root mirror pool so that if patching fails then I can boot from detached root mirror pool. Please let me know how can I detach root pool
bash-3.2# zpool status
pool: rpool
state: ONLINE... (5 Replies)
Discussion started by: hb00
5 Replies
LEARN ABOUT DEBIAN
dpm-addpool
DPM-ADDPOOL(1) DPM Administrator Commands DPM-ADDPOOL(1)NAME
dpm-addpool - define a new disk pool
SYNOPSIS
dpm-addpool --poolname pool_name --def_filesize defsize [ --def_lifetime def_lifetime ] [ --def_pintime defpintime ] [ --gc_start_thresh
perc ] [ --gc_stop_thresh perc ] [ --gid pool_gids ] [ --group pool_groups ] [ --help ] [ --max_lifetime max_lifetime ] [ --max_pintime
maxpintime ] [ --ret_policy retention_policy ] [ --s_type space_type ]
DESCRIPTION
dpm-addpool defines a new disk pool.
This command requires ADMIN privilege.
OPTIONS
pool_name
specifies the disk pool name. It must be at most CA_MAXPOOLNAMELEN characters long.
defsize
specifies the default amount of space reserved for a file. This is by default in bytes, but the number may also be post-fixed with
'k', 'M' or 'G' for kilobyte, Megabyte and Gigabyte respectively.
def_lifetime
specifies the default time a space or volatile file is kept in the system (in seconds).
defpintime
specifies the default time a file is kept on a given disk (in seconds).
gc_start_thresh
specifies the minimum free space in the pool. If the percentage of free space goes below this value, the garbage collector is
started. Default is 0.
gc_stop_thresh
specifies the percentage of free space in the pool above which the garbage collector is stopped. Default is 0.
max_lifetime
specifies the maximum time a space or volatile file is kept in the system (in seconds).
maxpintime
specifies the maximum time a file is kept on a given disk (in seconds).
pool_gids
if not zero, the disk pool is restricted to this comma separated list of group gids.
pool_groups
if set and not "ALL", the disk pool is restricted to this comma separated list of group names.
retention_policy
specifies the retention policy supported by the disk pool. It can be R (for Replica), O (for Output) or C (for Custodial). Default
is R.
space_type
indicates the type of space supported in the disk pool. It can be V (for Volatile), D (for Durable), P (for Permanent) or - (to
accept any type). The latter is the default.
EXAMPLE
dpm-addpool --poolname Volatile --def_filesize 200M --s_type V
EXIT STATUS
This program returns 0 if the operation was successful or >0 if the operation failed.
SEE ALSO dpm(1), dpm_addpool(3)LCG $Date: 2010-02-05 10:50:58 +0100 (Fri, 05 Feb 2010) $ DPM-ADDPOOL(1)