Does anyone know how to force these rogue logical volumes to mirror to there respective disks?
DISK:Logical Volumes
03:cw_p05,cw_p01_01,cw_p01_02,lv00
09:cw_p05,cw_p01_01,cw_p01_02
04:cw_p01_phyldbs,cw_p01_03,cw_op01_01,cw_od01
10:cw_p01_phyldbs,cw_p01_03,cw_op01_01 (1 Reply)
I hope I am posting in the correct forum.
I have a server - which I am installing solaris 9 on.
The server currently has 2 disks. I wish to run solaris 9 on one, and use the other as a mirror for the first one. ie. If the first one should ever fail, then I can swap to the mirror and just... (18 Replies)
I've looked a little but haven't found a solid answer, assuming there is one.
What's better, hardware mirroring or ZFS mirroring? Common practice for us was to use the raid controllers on the Sun x86 servers. Now we've been using ZFS mirroring since U6. Any performance difference? Any other... (3 Replies)
Hi ,
I am new to SVM .when i try to learn RAID 1 , first they are creating two RAID 0 strips through
metainit d51 1 1 c0t0d0s2
metainit d52 1 1 c1t0d0s2
In the next step
metainit d50 -m d51
d50: Mirror is setup
next step is
metaattach d50 d52
d50 : submirror d52 is... (7 Replies)
Hi guys,
We had created a pool as follows:
zpool create filing_pool raidz c1t2d0 c1t3d0 ........
Due to some requirement, we need to destroy the pool and re-create another one. We wish to know now which disks have been included in the filing_pool, how do we list the disks used to create... (2 Replies)
i have this pool1 on my sun4u sparc machine
bash-3.00# zpool get all pool1
NAME PROPERTY VALUE SOURCE
pool1 size 292G -
pool1 used 76.5K -
pool1 available 292G -
pool1 capacity 0% -... (1 Reply)
I have to do patching in single user mode in solaris 10 zfs root pool. Before that I have to detach the root mirror pool so that if patching fails then I can boot from detached root mirror pool. Please let me know how can I detach root pool
bash-3.2# zpool status
pool: rpool
state: ONLINE... (5 Replies)
Discussion started by: hb00
5 Replies
LEARN ABOUT OPENSOLARIS
zdb
zdb(1M) System Administration Commands zdb(1M)NAME
zdb - ZFS debugger
SYNOPSIS
zdb pool
DESCRIPTION
The zdb command is used by support engineers to diagnose failures and gather statistics. Since the ZFS file system is always consistent on
disk and is self-repairing, zdb should only be run under the direction by a support engineer.
If no arguments are specified, zdb, performs basic consistency checks on the pool and associated datasets, and report any problems
detected.
Any options supported by this command are internal to Sun and subject to change at any time.
EXIT STATUS
The following exit values are returned:
0 The pool is consistent.
1 An error was detected.
2 Invalid command line options were specified.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWzfsu |
+-----------------------------+-----------------------------+
|Interface Stability |Unstable |
+-----------------------------+-----------------------------+
SEE ALSO zfs(1M), zpool(1M), attributes(5)SunOS 5.11 31 Oct 2005 zdb(1M)