09-14-2011
scroll to the bottom of this page and follow the links!
9 More Discussions You Might Find Interesting
1. Solaris
Hi guys,
Hope somebody can help me on this. I have a Sun Sparc 20 workstation and it has a boot problem. During boot, an error message " ifconfig:socket: Bad File Number" come up and the workstation hang (cannot boot).
I did boot -s and checked using ifconfig -a command but i got the same... (0 Replies)
Discussion started by: kroegand
0 Replies
2. Solaris
Hi..i have installed solaris 10 on vmware. I m not able connect to internet.
pls help in detail. how to solve the problem. During the installation i have put no DHCP. cofigured manually ( Ip 192.168.1.9) default gateway 192.168.1.1 . (3 Replies)
Discussion started by: johnavery
3 Replies
3. Solaris
Hi there,
I'm trying to configure an additional network interface on Solaris 8 (eri0). The interface has been activated, but all the frames are still routed to the current default interface (ce0) I've tried following command (with various syntaxes...) unsuccessfully so far:
# route add... (2 Replies)
Discussion started by: sreiniche
2 Replies
4. Red Hat
Hi
I have installed OEL 4 on my dell XPS laptop. But when i connect the LAN cable and try to acesss internet. it does not work. the led's in the port do not blink when i plug in the cable .do i need some drivers please suggest.
Thanks
Ankur (2 Replies)
Discussion started by: ankurk
2 Replies
5. Solaris
Hi gurus
Could anybody tell me that what are the kernal parameter of network interface in solaris
Regards (3 Replies)
Discussion started by: girish.batra
3 Replies
6. Solaris
Hi,
/sbin/ifconfig -a
when i login as guest user , output like below,
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
eri0: flags=1004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 1500 index 2
inet... (5 Replies)
Discussion started by: forumguest
5 Replies
7. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
8. Solaris
Dear All,
I have a solaris Server in which I have 4 network interfaces , out of which only one is used . So all the applications are using this interface .
The interface speed is 1000Mbps . I find no hardware issue or packets g being dropped.
But i find that no of Input and Output... (4 Replies)
Discussion started by: jegaraman
4 Replies
9. Solaris
Hi, I am new in Solaris 11. I can't even make the NIC work. Here is the issue:
Any help will be greatly appreciated. (6 Replies)
Discussion started by: aixlover
6 Replies
LEARN ABOUT NETBSD
scroll
CURSES_SCROLL(3) BSD Library Functions Manual CURSES_SCROLL(3)
NAME
curses_scroll, scrl, wscrl scroll, scrollok, setscrreg, wsetscrreg -- curses window scrolling routines
LIBRARY
Curses Library (libcurses, -lcurses)
SYNOPSIS
#include <curses.h>
int
scrl(int n);
int
wscrl(WINDOW *win, int n);
int
scroll(WINDOW *win);
int
scrollok(WINDOW *win, boolf flag);
int
setscrreg(int top, int bottom);
int
wsetscrreg(WINDOW *win, int top, int bottom);
DESCRIPTION
These functions scroll areas on stdscr or on the specified window.
The scrl() function scrolls stdscr by n lines. If n is positive then then stdscr is scrolled up. n lines are lost from the top of stdscr
and n blank lines are inserted at the bottom. If n is negative then stdscr is scrolled down. n blank lines are inserted at the top of
stdscr and n lines are lost from the bottom.
The wscrl() function is the same as the scrl() function, excepting that it scrolls the window specified by win.
The scroll() function scrolls the window win up by one line.
The scrolling behaviour of a window can be controlled by using the scrollok() function. If the flag argument is TRUE then a line wrap at the
bottom of the window will cause the window to be scrolled up one line, if flag is FALSE then lines that would force a scroll will be trun-
cated.
The setscrreg() function sets up a software scrolling region on stdscr which will define a region of the screen that will be scrolled. The
scrolling of this region is also controlled by the scrollok() function.
The wsetscrreg() function does the same as the setscrreg() function, except that the scrolling region is set on the window specified by win.
If a scrolling region has been set with the setscrreg() or wsetscrreg() functions and the current cursor position is inside the scrolling
region, then only the area inside the scrolling region is scrolled.
RETURN VALUES
Functions returning pointers will return NULL if an error is detected. The functions that return an int will return one of the following
values:
OK The function completed successfully.
ERR An error occurred in the function.
SEE ALSO
curses_deleteln(3), curses_insdelln(3), curses_insertln(3)
STANDARDS
The NetBSD Curses library complies with the X/Open Curses specification, part of the Single Unix Specification.
HISTORY
The Curses package appeared in 4.0BSD.
BSD
August 12, 2002 BSD