09-14-2011
replacing the battery from the controller in DS4300
Currently we have this DS4300 issue, we found that we have to replace the two batteries. Each from each controller.
1) When poweroff the DS4300, when taking out the battery, will this affect or clear out the saved configuration of the local settings ?
2) If no, is there any documentation thats show that ?
Thank you for your help.
9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hello,
We're setting up a solution for a group of customers with 2 p520 servers and 1 DS4300 unit with 9 disks (at this stage). The meaning is to create two arrays on the DS4300. Both servers will be connected to the DS4300 unit and to both controllers (e.g. Controller 1 connected to server 1... (0 Replies)
Discussion started by: EricBE
0 Replies
2. Filesystems, Disks and Memory
Hello,
We're setting up a solution for a group of customers with 2 p520 servers and 1 DS4300 unit with 9 disks (at this stage). The meaning is to create two arrays on the DS4300. Both servers will be connected to the DS4300 unit and to both controllers (e.g. Controller 1 connected to server 1... (0 Replies)
Discussion started by: EricBE
0 Replies
3. AIX
Hi Guys,
It's me again with this unending support of AIX43 ML 9.
I finally able to test a migration from SSA to SAN, no problem. One problem, I bought some expansion of DS4300, two arrays. The IBM tech told me that before I can connect to the existing DS4300, I need to upgrade the firmware... (1 Reply)
Discussion started by: itik
1 Replies
4. AIX
Hello,
This morning we have added 6 new disks (73 Gb) to our DS4300, then created a new Array en then created a logical drive, after this was done, teh following error occourd on the last 3 (new)disks:
Date/Time: 22-4-08 6:56:26
Sequence number: 5472
Event type: 282D
Event category:... (1 Reply)
Discussion started by: topper
1 Replies
5. Solaris
Hi Guys,
What's the driver I needed for Solaris 8 and Solaris 10 for the DS4300, spark and intel base?
It's my first time to setup on Solaris with DS4300, please give me advise on how to make it work fine.
Thanks in advance,
itik (3 Replies)
Discussion started by: itik
3 Replies
6. Solaris
Hi everyone,
I changed the batteries on 29-Jun-2008 for the storedges.
But received error messages from the server today,I used the "-u" option to update the service date information but it syntaticaly fails. Why?
Jul 4 12:00:03 auriga SUNWscsdServer: <rctrl8001> The battery on... (3 Replies)
Discussion started by: incredible
3 Replies
7. Linux
Im running Ubuntu 9.04 and the battery indicator on my laptop always reads 0% no matter what. Whether im charging or discharging, the pop up says:
"Computer is running on battery power
Laptop battery discharging (0.0%)
Battery discharge time is currently unknown"
When plugged in it says... (2 Replies)
Discussion started by: Charbs
2 Replies
8. Solaris
Can someone point me to a procedure detailing the replacement of a failed battery in a SUN 6540 controller.
Or describe the procedure.
Thanks (1 Reply)
Discussion started by: USFE
1 Replies
9. AIX
Hi,
This is follow up to the post https://www.unix.com/aix/233361-san-disk-appearing-double-aix.html
When I connected Pseries Machine HBA Card ( Dual Port ) directly to the SAN Storage DS4300 , I was able to see Host Port Adapter WWN numbers , although I was getting this message... (2 Replies)
Discussion started by: filosophizer
2 Replies
LEARN ABOUT REDHAT
fentonups
FENTONUPS(8) Network UPS Tools (NUT) FENTONUPS(8)
NAME
fentonups - Driver for Fenton Technologies (Megatec protocol) UPS equipment
NOTE
This man page only documents the hardware-specific features of the fentonups driver. For information about the core driver, see nutups-
drv(8).
SUPPORTED HARDWARE
fentonups primarily supports Fenton Technologies models such as the PowerPal, PowerPure and PowerOn lines. Due to the common heritage of
UPS equipment, it generally supports other hardware that also uses the Megatec protocol.
At the time of this writing, the PowerGuard PG-600 and PowerCom SMK-800A are recognized and supported. Other Megatec units should also
work, but they will generate a warning since their battery information is not known.
EXTRA ARGUMENTS
This driver does not support any extra settings in the ups.conf(5).
BUGS
The battery percentage is derived from the voltage data that the UPS returns, since the UPS doesn't return that value directly. On some
hardware, the charge will remain at 100% for a long time and then drops quickly shortly before the battery runs out. You can confirm from
the BATTVOLT readings that this is a problem with the UPS and not this driver.
Similarly, the float from the charger in some models forces the battery charge percentage back up to 100% immedately after the UPS goes
back on-line, so you can't tell when it is really recharged.
Dead/broken batteries can't be reported reliably. If your UPS kills the load instantly or within seconds of starting the inverter, your
batteries probably need to be replaced. Recently, a pair of 3.5 hour outages here (thanks CPS!) finally killed my batteries. You may have
to run a manual test from the front panel before the "replace battery" LED will light.
AUTHOR
Russell Kroll
SEE ALSO
The core driver:
nutupsdrv(8)
Internet resources:
The NUT (Network UPS Tools) home page: http://www.exploits.org/nut/
NUT mailing list archives and information: http://lists.exploits.org/
Wed Oct 16 2002 FENTONUPS(8)