Sponsored Content
Operating Systems AIX Vscsi and npiv on same adapter Post 302554064 by dukessd on Friday 9th of September 2011 06:14:20 PM
Old 09-09-2011
Yep, both on the same adapter or even the same adapter port is no problem and fully supported.
 

10 More Discussions You Might Find Interesting

1. AIX

Anyone using NPIV?

Is anyone here using NPIV with AIX? If you are, what type of switch are you connected to? Also, please share some impressions of NPIV over traditional port-to-port LUN assignments. We are looking to move to NPIV and need some convincing argume... I mean information. (2 Replies)
Discussion started by: kah00na
2 Replies

2. AIX

Migrating hdisks from vscsi to NPIV with powerpath

Hi All, I'm preparing to migrate some servers from vscsi to pass-thru NPIV. I am planning to have the SAN team move the exact LUNs from vio1/vio2 to those two VWWN through NPIV. My question is on the partition itself.. right now, let's say I have hdisk0/1/2/3/4 that are part of datavg. They... (2 Replies)
Discussion started by: lapfrank
2 Replies

3. AIX

NPIV with 8Gb PCI Express Dual Port FC Adapter

All I am at a loss with a VIO server running ios 2.2.0.10-FP-24 SP-01. The VIO server is fitted with two 8Gb PCI Express Dual Port FC Adapters. However when I run the lsnports command only two of the adapter ports show as capable: $ lsnports name physloc ... (4 Replies)
Discussion started by: johnf
4 Replies

4. AIX

hdisk mapping to a vSCSi Adapter

Hello, I have a VIOS System and would like to do mapping some hdisks, hdisk160 until hdisk165 to a vSCSi Adapter. I try to do this in the oem_setup_env like the following: for i in $(lspv | grep hdisk* | awk {'print $1'}; do mkdev -V $i -p vhost20 done There where a mapping with... (4 Replies)
Discussion started by: torsten163
4 Replies

5. AIX

NPIV mapping problem

Hello all I hope someone can help me with this. I have a single LPAR which is supplied a rootvg and datavg disk set from a dual VIO server configuration. I see dual path disks for all the datavg disks but only see one path for the rootvg disks. The client LPAR has the following: fcs0 ... (3 Replies)
Discussion started by: johnf
3 Replies

6. AIX

NPIV custom WWN

Hi All :) i would like to know if i can customize the WWN of the new VFC (NPIV). Or, if i must move the LPAR on another server with another FCS, i have to change the zoning?? Thanks in advance. Mario ---------- Post updated 09-21-12 at 02:51 AM ---------- Previous update was 09-20-12 at... (1 Reply)
Discussion started by: Zio Bill
1 Replies

7. AIX

VIOS FC Mapping/NPIV questions

Please forgive me here as I don't fully understand what I am talking about here so if I use the wrong terminology please overlook me. We have multiple AIX LPARs on the managed system with two VIO Servers. A Co-Worker and I are trying to set up a new LPAR client (The guy that knows this is out)... (14 Replies)
Discussion started by: juredd1
14 Replies

8. AIX

How to put vscsi in available state?

Hello Friends, My question/problem is that I noticed 2 servers in my environment vscsi is showing up as defined (not available) or is defined and not showing the path to both vscsi's when ruining lspath command. I am new to AIX admin, work alone, and work in an small environment. My question is,... (12 Replies)
Discussion started by: Adnans2k
12 Replies

9. AIX

Devices.vscsi.disk ?

Hello, When I assigned CDROM from IVM (VIOS) to LPAR and then running cfgmgr i get the following message on the client lpar #cfgmgr cfgmgr: 0514-621 WARNING: The following device packages are required for device support but are not currently installed. devices.vscsi.disk searching... (0 Replies)
Discussion started by: filosophizer
0 Replies

10. AIX

Misconfiguration detected Adapter interface name en 3 Adapter offset 0

Hi, We had a hardware problem with an IBM System p5 server, with AIX 5.2 We restore from a tape the last backup we had, but the server does not boot up as expected. The server try to mount some directories from a storage, but could not comunicate with them, we check the FC and everything is... (12 Replies)
Discussion started by: trevian3969
12 Replies
asadmin-delete-resource-adapter-config(1AS)			   User Commands		       asadmin-delete-resource-adapter-config(1AS)

NAME
asadmin-delete-resource-adapter-config, delete-resource-adapter-config - deletes the configuration information created in domain.xml for the connector module SYNOPSIS
delete-resource-adapter-config --user admin_user [--password admin_password][--host localhost] [--port 4848][--secure|-s] [--passwordfile filename] [--terse=false] [--echo=false] [--interactive=true] raname Deletes the entry in the resource-adapter-config element of the domain.xml file with the provided --raname. This command is supported in remote mode only. OPTIONS
--user authorized domain application server administrative username. --password password to administer the domain application server. --host machine name where the domain application server is running. --port port number of the domain application server listening for administration requests. --secure if true, uses SSL/TLS to communicate with the domain application server. --passwordfile file containing the domain application server password. --terse indicates that any output data must be very concise, typically avoiding human-friendly sentences and favoring well- formatted data for consumption by a script. Default is false. --echo setting to true will echo the command line statement on the standard output. Default is false. --interactive if set to true (default), only the required password options are prompted. OPERANDS
raname the value kept in the resource-adapter-name in the domain.xml file. Example 1: Using delete-resource-adapter-config asadmin> delete-resource-adapter-config --username admin1 --password adminadmin myresourceadapter Command delete-resource-adapter-config executed successfully EXIT STATUS
0 command executed successfully 1 error in executing the command asadmin-create-resource-adapter-config(1AS), asadmin-list-resource-adapter-configs(1) J2EE 1.4 SDK March 2004 asadmin-delete-resource-adapter-config(1AS)
All times are GMT -4. The time now is 07:11 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy