Vscsi and npiv on same adapter Post: 302554010

10 More Discussions You Might Find Interesting

1. AIX

Anyone using NPIV?

Is anyone here using NPIV with AIX? If you are, what type of switch are you connected to? Also, please share some impressions of NPIV over traditional port-to-port LUN assignments. We are looking to move to NPIV and need some convincing argume... I mean information.

2. AIX

Migrating hdisks from vscsi to NPIV with powerpath

Hi All, I'm preparing to migrate some servers from vscsi to pass-thru NPIV. I am planning to have the SAN team move the exact LUNs from vio1/vio2 to those two VWWN through NPIV. My question is on the partition itself.. right now, let's say I have hdisk0/1/2/3/4 that are part of datavg. They...

3. AIX

NPIV with 8Gb PCI Express Dual Port FC Adapter

All I am at a loss with a VIO server running ios 2.2.0.10-FP-24 SP-01. The VIO server is fitted with two 8Gb PCI Express Dual Port FC Adapters. However when I run the lsnports command only two of the adapter ports show as capable: $ lsnports name physloc ...

4. AIX

hdisk mapping to a vSCSi Adapter

Hello, I have a VIOS System and would like to do mapping some hdisks, hdisk160 until hdisk165 to a vSCSi Adapter. I try to do this in the oem_setup_env like the following: for i in $(lspv | grep hdisk* | awk {'print $1'}; do mkdev -V $i -p vhost20 done There where a mapping with...

5. AIX

NPIV mapping problem

Hello all I hope someone can help me with this. I have a single LPAR which is supplied a rootvg and datavg disk set from a dual VIO server configuration. I see dual path disks for all the datavg disks but only see one path for the rootvg disks. The client LPAR has the following: fcs0 ...

6. AIX

NPIV custom WWN

Hi All :) i would like to know if i can customize the WWN of the new VFC (NPIV). Or, if i must move the LPAR on another server with another FCS, i have to change the zoning?? Thanks in advance. Mario ---------- Post updated 09-21-12 at 02:51 AM ---------- Previous update was 09-20-12 at...

7. AIX

VIOS FC Mapping/NPIV questions

Please forgive me here as I don't fully understand what I am talking about here so if I use the wrong terminology please overlook me. We have multiple AIX LPARs on the managed system with two VIO Servers. A Co-Worker and I are trying to set up a new LPAR client (The guy that knows this is out)...

8. AIX

How to put vscsi in available state?

Hello Friends, My question/problem is that I noticed 2 servers in my environment vscsi is showing up as defined (not available) or is defined and not showing the path to both vscsi's when ruining lspath command. I am new to AIX admin, work alone, and work in an small environment. My question is,...

9. AIX

Devices.vscsi.disk ?

Hello, When I assigned CDROM from IVM (VIOS) to LPAR and then running cfgmgr i get the following message on the client lpar #cfgmgr cfgmgr: 0514-621 WARNING: The following device packages are required for device support but are not currently installed. devices.vscsi.disk searching...

10. AIX

Misconfiguration detected Adapter interface name en 3 Adapter offset 0

Hi, We had a hardware problem with an IBM System p5 server, with AIX 5.2 We restore from a tape the last backup we had, but the server does not boot up as expected. The server try to mount some directories from a storage, but could not comunicate with them, we check the FC and everything is...

LEARN ABOUT PHP

httppower

httppower(8)							     powerman							      httppower(8)

NAME

       httppower - communicate with HTTP based power distribution units

SYNOPSIS

       httppower [--url URL]

DESCRIPTION

       httppower  is  a  helper program for powerman which enables it to communicate with HTTP based power distribution units.	It is run interac-
       tively by the powerman daemon.

OPTIONS

       -u, --url URL
	      Set the base URL.

INTERACTIVE COMMANDS

       The following commands are accepted at the httppower> prompt:

       auth user:pass
	      Authenticate to the base URL with specified user and password, using ``basic'' HTTP authentication which sends the user and password
	      over the network in plain text.

       seturl URL
	      Set the base URL.  Overrides the command line option.

       get [URL-suffix]
	      Send an HTTP GET to the base URL with the optional URL-suffix appended.

       post [URL-suffix] key=val[&key=val]...
	      Send an HTTP POST to the base URL with the optional URL-suffix appended, and key-value pairs as argument.

FILES

       /usr/sbin/httppower
       /etc/powerman/powerman.conf

ORIGIN

       PowerMan was originally developed by Andrew Uselton on LLNL's Linux clusters.  This software is open source and distributed under the terms
       of the GNU GPL.

SEE ALSO

       powerman(1), powermand(8), httppower(8), plmpower(8), vpcd(8), powerman.conf(5), powerman.dev(5), powerman-devices(7).

       http://sourceforge.net/projects/powerman

powerman-2.3.5							    2009-02-09							      httppower(8)