Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: DHCP/pxeboot Situation: how to specify default route?
Special Forums IP Networking DHCP/pxeboot Situation: how to specify default route? Post 302551682 by mock on Wednesday 31st of August 2011 09:46:03 AM
Old 08-31-2011
DHCP/pxeboot Situation: how to specify default route?
Greetings,

I am using debian squeeze to perform the following operation:

1. pxeboot Alix 2.c board into debian installer

When I get to the installer my laptop's dhcp server successfully provides an ip address but does not set up the default route. I am not sure how to provide this.

I am connected to a wireless network on the subnet 192.168.1.1/255.255.255.0.

The dhcp server is set up on 192.168.32.50 with the subnet specified as 192.168.32.0/255.255.255.0. In my /etc/network/interfaces file I set the gateway for this interface to 192.168.1.1 and in my /etc/dhcp/dhcpd.conf file I set the 192.168.32.0/255.255.255.0 subnet to have "options routers 192.168.1.1".

Am I missing something? Let me know if you need more info. And thanks in advance for your help! ...whoever you are
 

10 More Discussions You Might Find Interesting

1. AIX

Permanent Default Route

Hi, We are running AIX 5.2. Our default gateway used to be IP Address A. Our new default gateway is IP Address B. A netstat revealed that our default route was IP address A. We manually added default route with IP address B and removed the default route with IP address A. However,... (3 Replies)
Discussion started by: DenD
3 Replies

2. AIX

Default route removed - what to do ?

Hi, After accidental default route removal serial connection doesn't work. What should I do to connect to my machine ? thanks Vilius (7 Replies)
Discussion started by: vilius
7 Replies

3. Solaris

solaris 10 u5 what happens if no default route configured

Hi, I am new to solaris 10. What is the procedure the os takes if a default route is not configured? I am using a multihomed server with 4 interfaces. It looked strange to me this morning, because i had not defined a default route it defaulted to making one up, with the ip address of another... (9 Replies)
Discussion started by: borderblaster
9 Replies

4. UNIX for Advanced & Expert Users

Configuration servidor PXEBOOT

Well I'd like to know how I have to configure the tftpboot folder on a Ubuntu 9.04, from this server to boot the livecd of clonezilla on the client through pxe, for now this is what I have does not work. I have the file in the folder tftpboot vmlinuz and initrd.img from the iso file clonezilla... (0 Replies)
Discussion started by: antonioongp
0 Replies

5. AIX

Default route question

Hello I have a question regarding default route on AIX servers. (I am using a p5 5.3 TL9 machine). in my output of "lsattr -El inet0" I can see there are two routes like below. route net,-hopcount,0,,0,x.x.207.7 Route True route net,-hopcount,0,,0,x.x.202.129 Route True But... (9 Replies)
Discussion started by: gsabarinath
9 Replies

6. Solaris

Default route is configured, but seem to not work

Hiya, I got the default gateway set in /etc/defaultrouter file, however "netstat -nr" doesn't show anything like "default" in the routing table. As far as I know "netstat" on Solaris 10 u7 should show something like : Routing Table: IPv4 Destination Gateway Flags Ref ... (8 Replies)
Discussion started by: TomSu
8 Replies

7. AIX

Default Route add fails

AIX version 5.3 when I try to add default gateway # route add 0 192.168.100.254 Or # route add default 192.168.100.254 I get the error 0821-275 route: socket: The file access permissions do not allow the specified action. searching on google i came across similar... (5 Replies)
Discussion started by: filosophizer
5 Replies

8. IP Networking

Get DHCP relay interfaces IP address using DHCP

Hi All , please view the set up below: ------------------------------------------------------------------- | DHCP Server |-----------| ROUTER & |-----------| Clients | | 192.168.99.1 | - -<eth1>| DHCP-RELAY|<eth2>-- | 192.168.88.X | ... (2 Replies)
Discussion started by: gdangoor
2 Replies

9. Solaris

Default route in system

Hi All Recently we have faced issue in SUN server after reboot of node 2 default routs has been added to system as below IRE Table: IPv4 **Destination*************Mask***********Gateway**********Device Mxfrg Rtt***Ref Flg**Out**In/Fwd* -------------------- ---------------... (2 Replies)
Discussion started by: aaysa123
2 Replies

10. Red Hat

IP Route add default and make permanet

Hi all, actually i'm facing this problem, we have 2 NICs on our VM.s with REDHAT 7.2 release, we made the following set up as we needed to access them from both IP ip route flush all ip route add 10.130.11.0/24 dev eno2 tab 1 ip route add 10.130.10.0/24 dev eno1 tab 2 ip route add... (0 Replies)
Discussion started by: charli1
0 Replies

LEARN ABOUT DEBIAN

simple-cdd

SIMPLE-CDD(1)						      General Commands Manual						     SIMPLE-CDD(1)

NAME

       simple-cdd - create custom debian-installer CDs

SYNOPSIS

       simple-cdd [options]

OPTIONS

       --conf Specify a configuration file

       --dist Specify a distribution (etch, lenny, sid)

       --graphical-installer|-g
	      Enable graphical installer by default

       --serial-console|-s
	      Set defaults for serial console

       --do-mirror
	      Generate a local mirror

       --no-do-mirror
	      Do not generate a local mirror

       --profiles|-p
	      Select profiles (Examples in /usr/share/simple-cdd/profiles/ directory)

       --build-profiles|-b
	      Profiles only used while building the CD

       --auto-profiles|-a
	      Pre-select and automatically install these profiles

       --local-packages
	      List of packages to be included on CD's local package repository

       --locale
	      Select locale (language and country)

       --keyboard
	      Select keyboard (console-keymaps-at/keymap debconf question)

       --debian-mirror
	      Specify debian mirror (The default is: ftp://ftp.us.debian.org/debian)

       --security-mirror
	      Specify securty mirror (The default is: http://security.debian.org/)

       --mirror-tools
	      List the mirror tools to be used (The defaults are both wget and reprepro)

       --kernel-packages
	      List of kernel packages to be included on the CD

       --help|-h
	      Display the usage message

       --qemu|-q
	      Use qemu to test the built image

       --force-preseed
	      Only issue a warning if a preseeding file is invalid

       --profiles-udeb-dist
	      Specify distribution to pull simple-cdd-profiles udeb from

       --extra-udeb-dist
	      Specify additional distribution to pull udebs from

EXAMPLES

       simple-cdd --profiles x-basic -g
	      Build  a	custom	image  using  the  default  options,  except  for using the graphical installer by default and the x-basic profile
	      (/usr/share/simple-cdd/x-basic.*)

AUTHOR

       This manual page was written by Gustavo Franco <stratus@acm.org>, for the Debian project (but may be used for others).

								  Oct 28th, 2007						     SIMPLE-CDD(1)
All times are GMT -4. The time now is 11:09 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy