|
|
Sponsored Content
Top Forums
UNIX for Dummies Questions & Answers
find physical disk type : SAS / SATA
Post 302551528 by Corona688 on Tuesday 30th of August 2011 06:19:20 PM
08-30-2011
|
|
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello,
I need explanations about physical disks and physical volumes. What is the difference between these 2 things?
In fact, i am trying to understand what the AIX lspv2command does.
Thank you in advance. (2 Replies)
Discussion started by: VeroL
2 Replies
2. Red Hat
Hi All,
How do I verify the sata/sas controller status on my redhat 2.6?
Thanks.
Itik (1 Reply)
Discussion started by: itik
1 Replies
3. UNIX for Advanced & Expert Users
Hi All:
I am using an adaptor between a 1TB SATA hard drive and solaris 8 box with 68 pin scsi. I use the format utility to partition the HD which works fine but when I use newfs, I get some errors. I will place them below.
I have blocked and the error message is in red.
Anybody got any... (1 Reply)
Discussion started by: mndavies
1 Replies
4. Filesystems, Disks and Memory
Hello,
I wanted to share an experience I had today which was quite a learning experience and perhaps useful for others who may run into the issue at some point in the future.
Basically, the scenario involves a OS which was installed on a machine which hardware-wise, had a SATA Drive. The... (0 Replies)
Discussion started by: septima.pars
0 Replies
5. SCO
Is SATA hard disk is suooprted by SCO OpenServer 5.05? If No, how to couter this problem. If yes, please provide the installation steps. (2 Replies)
Discussion started by: rakeshkumar9919
2 Replies
6. Hardware
Hello everybody,
I need to connect a laptop 2.5 SATA hard drive to a Desktop board (which uses 3.5' SATA hard drives). I've tried the connectors and they fit excellent in the 2.5 SATA connectors.
The problem is that the laptop hard drive uses 5v and the PC's power source sends 12v. So, my... (4 Replies)
Discussion started by: Zykl0n-B
4 Replies
7. Hardware
Hi everyone
(see attachments)
I bought an HP Elitebook 8460p on eBay and it came with a password-locked Hitachi hard drive which I was told is the original hard drive. I don't know the password for the drive and running the diagnostics tools I see the hard drive is healthy. I tried booting... (9 Replies)
Discussion started by: milhan
9 Replies
8. AIX
OSLevel: 5300-10-02-0943
System Model: IBM,8203-E4A
Power 6
==
Hi!
I replaced a failed pdisk in the raid enclosure as follows,
- rmdev -l 'pdisk18' '-d'
- Replaced it.
- cfgmgr (detected)
- I can see the new drive, with the correct serial #
lscfg -v -l pdisk18
pdisk18... (2 Replies)
Discussion started by: estrar
2 Replies
9. AIX
Hello,
I would like to check how many SAS disks and its size per disk for the whole power system. As per my understanding, if we assign the SAS controller to LPAR, then we can see the disk in lpar smitty command.
How can we check from the Power machine(physical ones) as well? I think the... (5 Replies)
Discussion started by: Phat
5 Replies
LEARN ABOUT NETBSD
mfi
MFI(4) BSD Kernel Interfaces Manual MFI(4) NAME
mfi -- LSI Logic & Dell MegaRAID SAS RAID controller SYNOPSIS
mfi* at pci? dev ? function ? DESCRIPTION
The mfi driver provides support for the MegaRAID SAS family of RAID controllers, including: - Dell PERC 5/e, PERC 5/i, PERC 6/e, PERC 6/i - Intel RAID Controller SRCSAS18E, SRCSAS144E - LSI Logic MegaRAID SAS 8208ELP, MegaRAID SAS 8208XLP, MegaRAID SAS 8300XLP, MegaRAID SAS 8308ELP, MegaRAID SAS 8344ELP, MegaRAID SAS 8408E, MegaRAID SAS 8480E, MegaRAID SAS 8708ELP, MegaRAID SAS 8888ELP, MegaRAID SAS 8880EM2, MegaRAID SAS 9260-8i - IBM ServeRAID M1015, ServeRAID M5014 These controllers support RAID 0, RAID 1, RAID 5, RAID 6, RAID 10, RAID 50 and RAID 60 using either SAS or SATA II drives. Although the controllers are actual RAID controllers, the driver makes them look just like SCSI controllers. All RAID configuration is done through the controllers' BIOSes. mfi supports monitoring of the logical disks in the controller through the bioctl(8) and envstat(8) commands. EVENTS
The mfi driver is able to send events to powerd(8) if a logical drive in the controller is not online. The state-changed event will be sent to the /etc/powerd/scripts/sensor_drive script when such condition happens. SEE ALSO
intro(4), pci(4), scsi(4), sd(4), bioctl(8), envstat(8), powerd(8) HISTORY
The mfi driver first appeared in NetBSD 4.0. BSD
March 22, 2012 BSD