08-15-2011
i'm looking for cat5 and rj45 because it's cheaper.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Is anyone using a cable modem with unix and if so does your cable co. support unix or did you get that going on your own and how.
Thank you for all your help. (5 Replies)
Discussion started by: gparsons70
5 Replies
2. UNIX for Dummies Questions & Answers
hi , i have sparc machine , i want to connect my le0 (ethernet interface) directly to cable modem ,
i have created a file resolv.conf,hosts, dhcp.le0,defaultrouter,nisswitch,hostname.le0. i dont know my cable companies <domain name> and <name server assigned to me> , also they even dont know how... (5 Replies)
Discussion started by: raju
5 Replies
3. UNIX for Dummies Questions & Answers
I am new to Unix. I just got my SUN box from ebay with Solaris supposedly preloaded. The problem is I am unable to connect via Hyperterminal to Solaris, or more to the point, cannot tell if I have a successful connection and that solaris is the one not properly booted up.
I hooked up a null... (3 Replies)
Discussion started by: seethams
3 Replies
4. Solaris
HI all,
i still have a problem when using null modem to see the output from my server(sun ultra en 3000).
i followed the instruction from the internet, but it is not working.
1. i am using db9(5 4, 2 rows,put in laptop serial port) and db25(13 12, 2 rows,put in (A) server serial port).
2.... (3 Replies)
Discussion started by: waterbear
3 Replies
5. Solaris
Hi all,
Is there any difference between a null modem cable or a modem cable ?
i assume that a null modem cable is a normal cable that i used from cpu serial ports to a modem for dialup.
please correct if i am wrong,
thks (2 Replies)
Discussion started by: waterbear
2 Replies
6. Solaris
Hi All,
1. modify /etc/default/login file as
make commented # console=
2.put my laptops ip at both
/etc/inet/ipnodes and /etc/host file
still i can login via telnet/ftp through a DB9-serial cable, but when i tried
through a lan stratight cable directly connected that machine... (7 Replies)
Discussion started by: mahadib
7 Replies
7. Solaris
Hi Gurus,
Can I use null modem cable in Ultra sparc 10 workstation
Thanks (3 Replies)
Discussion started by: kumarmani
3 Replies
8. AIX
Current setup:
Some old AIX standalone machine (F series)
My WinXP laptop
Null modem cable from laptop to AIX machine (console port).
On Hypterminal on WinXP I can connect to the AIX machine (serial connection), but when I try to transfer file, it will just sit there. I'm guessing the... (3 Replies)
Discussion started by: apra143
3 Replies
9. AIX
I configured the serial modem in my P6-550 AIX 5.3 box
But i dont have telephone line.
when I run the command
# cu -l /dev/tty1
the output is as follows
does it mean that my modem is responding to the command?
can i say my serial port is working and communicating fine?
Connected
... (3 Replies)
Discussion started by: pchangba
3 Replies
DPT(4) BSD Kernel Interfaces Manual DPT(4)
NAME
dpt -- DPT RAID Controller SCSI driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device scbus
device dpt
For one or more EISA cards:
device eisa
For one or more ISA cards:
device isa
For one or more PCI cards:
device pci
To allow PCI adapters to use memory mapped I/O if enabled:
options DPT_ALLOW_MEMIO
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
dpt_load="YES"
DESCRIPTION
The dpt driver supports DPT RAID SCSI controllers.
SmartRAID (PM3???) are "Enterprise" class cards, and SmartCache (PM2???) cards are in the "Workstation" class. The Gen 4 Smart Cache IV
products were a re-issue of the Gen 3 utilizing upgraded (and cheaper to produce) silicon. The PM3334 (Smart RAID III) was not revamped as
there was no upgraded silicon (68040 processor) and it was using the best DPT made. Note there has been customer confusion over the faster
enterprise class card supported by this driver being an older generation. The Gen5 cards are supported by the asr(4) driver.
HARDWARE
The dpt driver provides support for the following RAID adapters:
o DPT Smart Cache Plus
o Smart Cache II (PM2?2?, PM2022 [EISA], PM2024/PM2124 [PCI]) (Gen2)
o Smart RAID II (PM3?2?, PM3021, PM3222)
o Smart Cache III (PM2?3?)
o Smart RAID III (PM3?3?, PM3332 [EISA], PM3334UW [PCI]) (Gen3)
o Smart Cache IV (PM2?4?, PM2042 [EISA], PM2044/PM2144 [PCI]) (Gen4)
o Smart RAID IV
SEE ALSO
asr(4), cd(4), ch(4), da(4), sa(4), scsi(4)
HISTORY
The dpt driver first appeared in FreeBSD 2.2.6.
AUTHORS
The dpt driver was written by Simon Shapiro and ported to the CAM SCSI system by Justin T. Gibbs.
BSD
June 18, 2006 BSD