08-11-2011
Quote:
Originally Posted by
Scrutinizer
Hi vishwamitra, well there is your answer. Your kernel command line says acpi=off, so then you cannot use acpi-cpufreq as long as you use acpi=off .
What should I do in that case ?
10 More Discussions You Might Find Interesting
1. Windows & DOS: Issues & Discussions
have a azuse mother borad 1600Mhz ram 512 hd 40gb
will not install windows want to finish but will not take it! Is this
a hard ware problem or a virus i use av norton 2002 and nod32
think got a virus not shure xp will not load any more (2 Replies)
Discussion started by: amicrawler2000
2 Replies
2. Programming
Hi there:
Thanks for clicking in first. I have a question here. I have a module that needs to be dynamically loaded when another piece of code needs it at runtime. I know that I will have to make a soname file before I can use it dynamically. My question is what commad I should use to make... (2 Replies)
Discussion started by: yanhu
2 Replies
3. Shell Programming and Scripting
i am studying a script which is used for data loading.
it has functions which deletes all the existing data before loading and then loads new fresh data.
but i am stuck up at function Replace into table ( col 1,col 2....)
Does this signify All Inserts. (1 Reply)
Discussion started by: ankitgupta
1 Replies
4. UNIX for Dummies Questions & Answers
I'm having a major problem trying to load a LPAR.
I've got through the HMC and shutdown and then activated the LPAR and it only gets to the Operator Panel Value of 0517. Now from some research I've found that this is to do with loading the rootvg. ( I think )
On the actual terminal all I get is... (0 Replies)
Discussion started by: KeesH
0 Replies
5. Solaris
I install a software xchm for opening chm files.
I install software and also its required libraries. But when i start it; no GUI appears. Application got halt. Process name also appears in process list when i run top command. Appliation continously using cpu but no GUI appears. Please tell me... (7 Replies)
Discussion started by: mansoorulhaq
7 Replies
6. UNIX for Advanced & Expert Users
I am using a SunBlade 100 system and accidently set a new alias for keyboard, now when it start it gives the following error,
The selected input device has no read routine. Keyboard not present using ttya for input and output.
Now i cannot execute any commands on the OBP and i just gets... (3 Replies)
Discussion started by: sumwhriblong
3 Replies
7. Linux
Hi masters,
I am new to linux and unix forum and this is my first forum. So please excuse if
I am not giving sufficient information. I will give them on request.
I have created a bandwidth manager module. I am using a 2.6.9 kernel and in Red Hat 3.4.3 distribution. But when i run make... (1 Reply)
Discussion started by: iamjayanth
1 Replies
8. Shell Programming and Scripting
Hi,
I have a strange issue in my script.
When script is run from command prompt it runs fine,but when run from cron it exist with error message.
I narrowed down the issue and found that " use Mail::Sender;" is the culprit.
If I comment the statment the code runs fine in both command and... (9 Replies)
Discussion started by: coolbhai
9 Replies
9. Solaris
Is there any link/tutorial on loading Solaris kernel modules at boot time?? (0 Replies)
Discussion started by: unisolin
0 Replies
10. Fedora
Well, I followed the steps in the Debian wiki here to install the drivers for the following video card:
$ lspci | grep VGA
03:00.0 VGA compatible controller: NVIDIA Corporation GF104 (rev a1)I confirmed the correct driver is installed. As you probably see I've tried this a few times and a few... (1 Reply)
Discussion started by: Azrael
1 Replies
LEARN ABOUT DEBIAN
acpi_video
ACPI_VIDEO(4) BSD Kernel Interfaces Manual ACPI_VIDEO(4)
NAME
acpi_video -- ACPI Video Extensions driver
SYNOPSIS
device acpi_video
DESCRIPTION
This driver uses the ACPI Video Extensions to control display switching and backlight brightness. The availability of the sysctl(8) vari-
ables depends on the functions offered by the host's ACPI implementation.
SYSCTL VARIABLES
The following sysctls are currently implemented, where <device> is crt, lcd, or tv:
hw.acpi.video.<device>.active
Current state of the output device.
hw.acpi.video.<device>.levels
List of supported brightness levels.
hw.acpi.video.<device>.brightness
Current brightness level of the device.
hw.acpi.video.<device>.fullpower
Preset brightness level to be used in full power mode.
hw.acpi.video.<device>.economy
Preset brightness level to be used in economy mode.
Defaults for these variables can be set in sysctl.conf(5), which is parsed at boot-time.
SEE ALSO
acpi(4), loader.conf(5), sysctl.conf(5), sysctl(8)
HISTORY
The acpi_video driver first appeared in FreeBSD 5.3.
AUTHORS
The acpi_video driver was written by Taku YAMAMOTO <taku@cent.saitama-u.ac.jp>. This manual page was written by Mark Santcroos
<marks@ripe.net>.
BUGS
Some systems only perform output switching via SMM even though they export the proper information via ACPI. On such systems, the proper
hotkeys or OEM driver (for example, acpi_toshiba(4)) must be used instead.
BSD
November 8, 2004 BSD