Hi,
I've recently mirrored the 4 disks in a V440. Disks 0 + 1 have been mirrored with hardware mirroring using the command raidctl -c c1t0d0 c1t2d0, the other 2 disks have been mirrored using Soltisce Disk Suite. I know how to check the progress for the SDS mirroring but how can I find the... (2 Replies)
Hello Gurus!!
Very recently i tried to mount a USB pen drive onto my solaris 10 (X4170 model) server. As i understand, in ideal scenarios it should get mounted automatically, but it did not happen. Neither anything is shown in "iostat -En" output or "rmformat -l" about the pen drive.
I also... (10 Replies)
Hello, I have 4 drives (500G each) in a raid 10, I got a power failior and this is the result?
cat /proc/mdstat
Personalities :
md126 : inactive sdb sdc sdd sde
1953536528 blocks super external:-md127/0
md127 : inactive sdd(S) sde(S) sdb(S) sdc(S)
9028 blocks super... (3 Replies)
Hi everyone,
I am not sure if I understand how mdadm --create /dev/md0 --level=container works?
A device called /dev/md0 appears in /proc/mdstat but I am not sure how to use that device?
I have 2 blank drives with 1 500GB partition on each. I would like to setup mirroring, but not in the... (0 Replies)
Trying to mount an external 160GB Toshiba drive but....
this is my dmesg tail output:
usb 2-2: new high speed USB device using ehci_hcd and address 3
usb 2-2: New USB device found, idVendor=13fd, idProduct=1618
usb 2-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 2-2:... (4 Replies)
had this RHEL 5 installation with /dev/sda1 and /dev/sda2 running..
created two more partitions /dev/sdj1 and /dev/sdj2 , the same sized partition as /dev/sda
trying to use mdadm to create RAID1 ..
I cannot even do it in "rescue" mode, I wonder if it can be done..
it kept... (2 Replies)
Hi
I am using SUSE 11 linux
I have couple of "nfs" entries in /etc/fstab which are automatically loaded after system restart.
One of the entry is windows drive mounted using cifs as shown below
//IP-Address/Partition /mnt/x cifs credentials=/creds/.creds,rw,uid=<name> 0 0
I want to... (1 Reply)
Hello,
i have a system with 6 sata3 seagate st3000dm01 disks running on stable Debian with software raid mdadm. i have md0 for root and md1 for swap and md2 for the files. i now want to add one more disk = sdh4 for md2 but i got this errors:
The new disk is connected to an 4 port sata... (7 Replies)
I am connecting a USB mass storage removeable drive to Solaris 10 x86 machine.
The device is detected and i am able to perform standard read and write functions.
But i want to use a code to send IOCTL based SCSI commands to the same device to read and write the data. Which i am unable to do so.... (17 Replies)
Hi fellow members!
I have a oracle solaris server with two internal disks, that acts as an authentication server only, and for now the server seems to be doing its job, but when typing metastat -c I get some notifications.
I am not familiar with SVM, I wonder if someone can help me on this:... (3 Replies)
Discussion started by: fretagi
3 Replies
LEARN ABOUT NETBSD
mlxctl
MLXCTL(8) BSD System Manager's Manual MLXCTL(8)NAME
mlxctl -- Mylex DAC960 family management utility
SYNOPSIS
mlxctl [-f dev] [-v] [-a] status [drive] [...]
mlxctl [-f dev] [-a] detach [drive] [...]
mlxctl [-f dev] [-a] check [drive] [...]
mlxctl [-f dev] rebuild channel:target
mlxctl [-f dev] cstatus
mlxctl [-f dev] rescan
mlxctl [-f dev] config
DESCRIPTION
The mlxctl utility performs status monitoring and management functions for Mylex DAC960 RAID controllers and attached devices.
The following options are available:
-a Apply the action to all drives attached to the controller.
-f dev Specify the control device to use. The default is /dev/mlx0.
-v Increased verbosity.
The following commands are available:
cstatus Display the controller's current status.
status Display the status of the specified drives. This command returns 0 if all drives tested are online, 1 if one or more drives are
critical and 2 if one or more are offline.
rescan Re-scan the logical drive table, and attach or detach devices from the system as necessary.
detach Detach the specified drives. Drives must be unmounted and unopened for this command to succeed.
check Initiate a consistency check and repair pass on a drive that provides redundancy (e.g., RAID1 or RAID5). This command returns imme-
diately. The status command can be used to monitor the progress of the check.
rebuild Rebuild onto the specified physical drive. Note that there can be only one running rebuild operation per controller at any given
time. This command returns immediately. The cstatus command can be used to monitor the progress of the rebuild.
config Write the current system drive configuration to stdout.
EXAMPLES
Display the status of drive ld3 attached to the controller mlx1:
mlxctl -f /dev/mlx1 -v status ld3
SEE ALSO ld(4), mlx(4)HISTORY
The mlxctl command first appeared in NetBSD 1.5.3, and was based on the mlxcontrol utility found in FreeBSD.
BUGS
Modifying drive configuration is not yet supported.
Some commands do not work with older firmware revisions.
Error log extraction is not yet supported.
BSD April 10, 2000 BSD