07-26-2011
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. Gentoo
Hi all,
I'm trying to write a script that will turn off the network interface eth0 on a linux Gentoo machine and then turn it back on, any help?
Thanks,
Neked (1 Reply)
Discussion started by: neked
1 Replies
3. Solaris
Hi all,
Here im facing problem with NIC Interface with my X86 Version of Solaris Express, even after loading module for that Interface. So please check this below mentioned log for your use and get back to me ASAP.
- - - -- --... (0 Replies)
Discussion started by: baraghun
0 Replies
4. Solaris
hi,
i have sunfire 280r sparc. i would like to know how to setup interface with command ndd line and put it in the file permanently.
my card is eri0 and speed can be 100mb or 1000mb full duplex.
thanks in advance. (3 Replies)
Discussion started by: lamoul
3 Replies
5. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
6. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
7. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
8. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT SUNOS
suninstall
suninstall(1M) System Administration Commands suninstall(1M)
NAME
suninstall - install the Solaris operating system
SYNOPSIS
suninstall
DESCRIPTION
install-solaris(1M) is now the preferred command for starting and restarting the Solaris Installation program. It should be used instead of
suninstall. suninstall is symbolically linked to install-solaris.
suninstall is a forms-based and graphical subsystem for installing the operating system.
suninstall exists only on the Solaris installation media (CD or DVD) and should only be invoked from there. Refer to the Solaris 10 Instal-
lation Guide: Basic Installations for more details.
suninstall allows installation of the operating system onto any standalone system. suninstall loads the software available on the installa-
tion media. Refer to the Solaris 10 Installation Guide: Basic Installations for disk space requirements.
USAGE
Refer to the Solaris 10 Installation Guide: Basic Installations for more information on the various menus and selections.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcdrom (Solaris instal- |
| |lation media) |
+-----------------------------+-----------------------------+
SEE ALSO
pkginfo(1), install(1M), install-solaris(1M), pkgadd(1M), attributes(5)
Solaris 10 Installation Guide: Basic Installations
NOTES
It is advisable to exit suninstall by means of the exit options in the suninstall menus.
SunOS 5.10 9 Sep 2004 suninstall(1M)