create the file /etc/dhcp.interface. in your case,
network service will look for this file to configure the interface for dhcp everytime you reboot the machine.
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem?
I am using the command:
ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up
I am running Solaris 9 OS. (2 Replies)
I have searched this forum for solution and have drawn a blank... so I come to you for help :)
I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Hi everyone, I recently inherited an IBM RS/6000 43P 150, and it appears that the on board ethernet is dead. Can I put in a PCI ethernet card and use that as the default ethernet connection (as opposed to the one on the motherboard)? If so, what type of card can I use and how does one configure... (2 Replies)
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do?
Thanks in advance (2 Replies)
Hi,
we have SUN Gigabit ethernet cards at the server, both have 2 lines connected but hiw can I found out which cable is on which port before I configure it: the cards has 4 ports , from right to left the cables are connected at the first right then 2 empty then the last at the left side.
... (1 Reply)
Discussion started by: manni2
1 Replies
LEARN ABOUT V7
dhcp
dhcp(5) Standards, Environments, and Macros dhcp(5)NAME
dhcp - Dynamic Host Configuration Protocol
DESCRIPTION
Dynamic Host Configuration Protocol (DHCP) enables host systems in a TCP/IP network to be configured automatically for the network as they
boot. DHCP uses a client/server mechanism: servers store configuration information for clients, and provide that information upon a
client's request. The information can include the client's IP address and information about network services available to the client.
This manual page provides a brief summary of the Solaris DHCP implementation.
Solaris DHCP Client
The Solaris DHCP client is implemented as background daemon, dhcpagent(1M). This daemon is started automatically during bootup if there
exists at least one dhcp.interface file in /etc. Only interfaces with a corresponding /etc/dhcp.interface file are automatically configured
during boot. Network parameters needed for system configuration during bootup are extracted from the information recieved by the daemon
through the use of the dhcpinfo(1) command. The daemon's default behavior can be altered by changing the tunables in the /etc/default/dhc-
pagent file. The daemon is controlled by the ifconfig(1M) utility. Check the status of the daemon using the netstat(1M) and ifconfig(1M)
commands.
Solaris DHCP Server
The Solaris DHCP server is implemented as a background daemon, in.dhcpd(1M). This daemon can deliver network configuration information to
either BOOTP or DHCP clients. The Solaris DHCP service can be managed using the dhcpmgr(1M) GUI or the command line utilities dhcpcon-
fig(1M), dhtadm(1M), and pntadm(1M).
DHCP Configuration Tables
The Solaris DHCP server stores client configuration information in the following two types of tables:
dhcptab tables Contain macros and options (also known as symbols), used to construct a package of configuration information to
send to each DHCP client. There exists only one dhcptab for the DHCP service. The dhcptab(4) can be viewed and mod-
ified using the dhtadm(1M) command or dhcpmgr(1M) graphical utility. See dhcptab(4) for more information about the
syntax of dhcptab records. See dhcp_inittab(4) for more information about the DHCP options and symbols.
DHCP network tables DHCP network tables, which contain mappings of client IDs to IP addresses and parameters associated with those
addresses. Network tables are named with the IP address of the network, and can be created, viewed, and modified
using the pntadm command or dhcpmgr graphical utility. See dhcp_network(4) for more information about network
tables.
SEE ALSO dhcpinfo(1), dhcpagent(1M), dhcpconfig(1M), dhcpmgr(1M), dhtadm(1M), ifconfig(1M), in.dhcpd(1M), netstat(1M), pntadm(1M), syslog(3C),
dhcp_network(4), dhcptab(4), dhcpsvc.conf(4), dhcp_inittab(4), dhcp_modules(5)
Solaris DHCP Service Developer's Guide
Alexander, S., and R. Droms. RFC 2132, DHCP Options and BOOTP Vendor Extensions. Silicon Graphics, Inc. Bucknell University. March 1997.
Droms, R. RFC 1534, Interoperation Between DHCP and BOOTP. Bucknell University. October 1993.
Droms, R. RFC 2131, Dynamic Host Configuration Protocol. Bucknell University. March 1997.
Wimer, W. RFC 1542, Clarifications and Extensions for the Bootstrap Protocol. Carnegie Mellon University. October 1993.
SunOS 5.10 13 Mar 2001 dhcp(5)