Device eth0 issue Post: 302539957

5 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

Eth err: "3c501 device eth0 does not seem to be present"

HI, When I do 'service network restart' , I am getting the following error. "3c501 device eth0 does not seem to be present, delaying initialization" Can any one suggest me the cause/solution for this? When I do 'lspci' it is showing the ehternet card as " Ethernet controller"Marvell...

2. AIX

How to find all device on p570 when need do device firmware upgrade?

I need upgrade firmware for the device of p570, when I go to IBM FIX download website, there are a lot of device of p570 listed. How can I know what device I have on my p570?

3. Solaris

Global device issue in sun cluster3.2

In my 2 node cluster (sun cluster3.2) running on x86 VMs. One of my nodes VM1 does not have the global devices populated due to which i cannot failover my file system to node VM1 , what could be the reason for this and how can i rectify it ? VM1:/>cd /dev/global -bash: cd: /dev/global: No...

4. Red Hat

Unable To Activate Ethernet Network Device in RHEL 5.5 - e100 device eth0 does not seem to be presen

Hi All, Could anyone please help to resolve the below problem. I installed RHEL5.5 in my desktop.But when i try to activate the ethernet connection then it gives me the error. I spent 2 days for the above and go through with several suggestion found by googling. But no luck. ...

5. HP-UX

Failed to open tape device /dev/rmt/0mn:Device busy (errno = 16)

Hi, Unable to make tape backup, please help. /opt/ignite/bin/make_tape_recovery -a /dev/rmt/?mn -I -v -m tar -x inc_entire=vg00 * Creating local directories for configuration files and archive. ======= 04/25/16 16:28:08 IST Started /opt/ignite/bin/make_tape_recovery. (Mon...

LEARN ABOUT DEBIAN

ex

EX(4)							 BSD/i386 Kernel Interfaces Manual						     EX(4)

NAME

     ex -- Ethernet device driver for the Intel EtherExpress Pro/10 and Pro/10+

SYNOPSIS

     To compile this driver into the kernel, place the following line in your kernel configuration file:

	   device ex

     Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):

	   if_ex_load="YES"

DESCRIPTION

     The ex driver provides support for Ethernet adapters based on the Intel i82595 chip.

     On the ISA bus, the card will be searched for in the I/O address range 0x200 - 0x3a0.  The IRQ will be read from the EEPROM on the card.  For
     correct operation Plug-N-Play support should be disabled.

     On the PC Card bus, the card will be automatically recognized and configured.

HARDWARE

     The ex driver supports the following Ethernet adapters:

     o	 Intel EtherExpress Pro/10 ISA
     o	 Intel EtherExpress Pro/10+ ISA
     o	 Olicom OC2220 Ethernet PC Card
     o	 Olicom OC2232 Ethernet/Modem PC Card
     o	 Silicom Ethernet LAN PC Card
     o	 Silicom EtherSerial LAN PC Card

DIAGNOSTICS

     ex%d: Intel EtherExpress Pro/10, address %6D, connector %s  The device probe found an installed card, and was able to correctly install the
     device driver.

     ex%d: WARNING: board's EEPROM is configured for IRQ %d, using %d  The device probe detected that the board is configured for a different
     interrupt than the one specified in the kernel configuration file.

     ex%d: invalid IRQ.  The device probe detected an invalid IRQ setting.

SEE ALSO

     arp(4), netintro(4), ng_ether(4), ifconfig(8)

HISTORY

     The ex device driver first appeared in FreeBSD 2.2.

AUTHORS

     The ex device driver was written by Javier Martin Rueda.  The PC Card attachment was written by Mitsuru ISAWAKI and Warner Losh.  This manual
     page was written by David E. O'Brien.

BUGS

     Currently the driver does not support multicast.

     The Silicom EtherSerial card's serial port does not currently work.  The Olicom OC2232 PC Card should work with the ex driver, but is cur-
     rently completely broken.

BSD
								   July 16, 2005							       BSD