07-19-2011
Only displays "lo" and "sit0".
I have tried adding the eth0 config using system-config-network but the HP NIC that I use does not appear to be listed on the list of interface devices?
5 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
HI,
When I do 'service network restart' , I am getting the following error.
"3c501 device eth0 does not seem to be present, delaying initialization"
Can any one suggest me the cause/solution for this?
When I do 'lspci' it is showing the ehternet card as
" Ethernet controller"Marvell... (2 Replies)
Discussion started by: praveen_b744
2 Replies
2. AIX
I need upgrade firmware for the device of p570, when I go to IBM FIX download website, there are a lot of device of p570 listed. How can I know what device I have on my p570? (4 Replies)
Discussion started by: rainbow_bean
4 Replies
3. Solaris
In my 2 node cluster (sun cluster3.2) running on x86 VMs. One of my nodes VM1 does not have the global devices populated due to which i cannot failover my file system to node VM1 , what could be the reason for this and how can i rectify it ?
VM1:/>cd /dev/global
-bash: cd: /dev/global: No... (1 Reply)
Discussion started by: fugitive
1 Replies
4. Red Hat
Hi All,
Could anyone please help to resolve the below problem.
I installed RHEL5.5 in my desktop.But when i try to activate the ethernet connection then it gives me the error.
I spent 2 days for the above and go through with several suggestion found by googling. But no luck.
... (0 Replies)
Discussion started by: Tanmoy
0 Replies
5. HP-UX
Hi,
Unable to make tape backup, please help.
/opt/ignite/bin/make_tape_recovery -a /dev/rmt/?mn -I -v -m tar -x inc_entire=vg00
* Creating local directories for configuration files and archive.
======= 04/25/16 16:28:08 IST Started /opt/ignite/bin/make_tape_recovery.
(Mon... (4 Replies)
Discussion started by: anuragr
4 Replies
veth(4) Linux Programmer's Manual veth(4)
NAME
veth - Virtual Ethernet Device
DESCRIPTION
The veth devices are virtual Ethernet devices. They can act as tunnels between network namespaces to create a bridge to a physical network
device in another namespace, but can also be used as standalone network devices.
veth devices are always created in interconnected pairs. A pair can be created using the command:
# ip link add <p1-name> type veth peer name <p2-name>
In the above, p1-name and p2-name are the names assigned to the two connected end points.
Packets transmitted on one device in the pair are immediately received on the other device. When either devices is down the link state of
the pair is down.
veth device pairs are useful for combining the network facilities of the kernel together in interesting ways. A particularly interesting
use case is to place one end of a veth pair in one network namespace and the other end in another network namespace, thus allowing communi-
cation between network namespaces. To do this, one first creates the veth device as above and then moves one side of the pair to the other
namespace:
# ip link set <p2-name> netns <p2-namespace>
ethtool(8) can be used to find the peer of a veth network interface, using commands something like:
# ip link add ve_A type veth peer name ve_B # Create veth pair
# ethtool -S ve_A # Discover interface index of peer
NIC statistics:
peer_ifindex: 16
# ip link | grep '^16:' # Look up interface
16: ve_B@ve_A: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc ...
SEE ALSO
clone(2), network_namespaces(7), ip(8), ip-link(8), ip-netns(8)
Linux 2018-02-02 veth(4)