Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Hi
I have installed OEL 4 on my dell XPS laptop. But when i connect the LAN cable and try to acesss internet. it does not work. the led's in the port do not blink when i plug in the cable .do i need some drivers please suggest.
Thanks
Ankur (2 Replies)
Hi,
I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface.
Please advise how to configure network interfaces using VMware. (1 Reply)
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
I have a few non-globa zones running in a 10.10.xx.xx network on a machine that is on a 192.168.xx.xx network.
My goal is to allow each of the non-global zones to communicate to each other while not communicating on the 192.168.xx.xx network.
I am using the current version of Solaris 10 in... (7 Replies)
Discussion started by: BradJM
7 Replies
LEARN ABOUT X11R4
defaultrouter
defaultrouter(4) File Formats defaultrouter(4)NAME
defaultrouter - configuration file for default router(s)
SYNOPSIS
/etc/defaultrouter
DESCRIPTION
The /etc/defaultrouter file specifies a IPv4 host's default router(s).
The format of the file is as follows:
IP_address
...
The /etc/defaultrouter file can contain the IP addresses or hostnames of one or more default routers, with each entry on its own line. If
you use hostnames, each hostname must also be listed in the local /etc/hosts file, because no name services are running at the time that
defaultrouter is read.
Lines beginning with the ``#'' character are treated as comments.
The default routes listed in this file replace those added by the kernel during diskless booting. An empty /etc/defaultrouter file will
cause the default route added by the kernel to be deleted.
Use of a default route, whether received from a DHCP server or from /etc/defaultrouter, prevents a machine from acting as an IPv4 router.
You can use routeadm(1M) to override this behavior.
FILES
/etc/defaultrouter Configuration file containing the hostnames or IP addresses of one or more default routers.
SEE ALSO in.rdisc(1M), in.routed(1M), routeadm(1M), hosts(4)SunOS 5.10 17 Aug 2004 defaultrouter(4)