07-04-2011
Network File System using HACMP
Hi,
I have an HACMP cluster with two nodes. The Resource Group contains a VG which in turn has a FS created in it say /test.. Now I want that FS to be mounted through NFS on some other AIX servers as well. What would be the best way to do this?
Regards,
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
I was given this question and cannot seem to answer it. "Identify 4 network and 4 sytem files that control how the system and network function (other than rc files)." The problem is I only know of rc files. Can anyone help? (2 Replies)
Discussion started by: trip
2 Replies
2. AIX
I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not... (1 Reply)
Discussion started by: johnf
1 Replies
3. Shell Programming and Scripting
say i have a system on thats on a network with access to the internet.
now, i have sensitive information on this system and i do not want the system to be connected to the outside world anymore. how do i get it off the network without actually having to disconnect the cables?
i'm asking this... (4 Replies)
Discussion started by: Terrible
4 Replies
4. Solaris
Hi all,
Kind of an emergency situation, I have to NFS mount an AIX filesystem on to a Sun Solaris OS (5.10).
Typically from Sun to Sun is:
mount -F nfs <remote file system>/dir <mount point>
Which of course doesn't work if the remote file system is another OS (like AIX).
Is there... (1 Reply)
Discussion started by: jeffpas
1 Replies
5. Linux
The Network Audio System (NAS)
Anybody have any luck with nasd or xmms-nas with any 2.6 distribution?
Works fine under FreeBSD (6.0/7.0). (0 Replies)
Discussion started by: ramen_noodle
0 Replies
6. AIX
Hi, I try to understand how to configure my ethernet network in a hacmp cluster.
I have 2 nodes, 3 lan port on each node, and 1 service ip to cluster.
I don't have any serial o iscsi heartbeat.
Do you suggest me a possibile ip address configuration? I've many error whene I verify it from hacmp... (3 Replies)
Discussion started by: hacmp
3 Replies
7. AIX
Hi all,
I was wondering if someone direct me in how to Make system backup for 2 nodes HACMP cluster ( system image ) .
What are the consideration for this task (3 Replies)
Discussion started by: h@foorsa.biz
3 Replies
8. AIX
hi,
when I do a failover, hacmp always starts db2 but recently it fails to start db2..noticed the issue is db2nodes.cfg is not modified by hacmp and is still showing primary node..manually changed the node name to secondary after which db2 started immediately..unable to figure out why hacmp is... (4 Replies)
Discussion started by: gkr747
4 Replies
9. AIX
Hi
I'm a little rusty with HACMP, but wanted to find out if it is possible to remove a disk heartbeat network from a running HACMP cluster.
Reason is, I need to migrate all the SAN disk, so the current heartbeat disk will be disappearing. Ideally, I'd like to avoid taking the cluster down to... (2 Replies)
Discussion started by: cmcbugg
2 Replies
10. AIX
Hi
I have a doubt. Our setup is a 2 node HACMP cluster. To create a HACMP file system we do via #smitty hacmp -> cspoc.
Imagine if I have done a mistake and created the file system locally in one of the node using #smitty crfs. How to bring this file system now under HACMP? (4 Replies)
Discussion started by: newtoaixos
4 Replies
cmruncl(1m) cmruncl(1m)
NAME
cmruncl - run a high availability cluster
SYNOPSIS
cmruncl [-f] [-v] [-n node_name...] [-t | -w none]
DESCRIPTION
cmruncl causes all nodes in a configured cluster or all nodes specified to start their cluster daemons and form a new cluster.
To start a cluster, a user must either be superuser(UID=0), or have an access policy of FULL_ADMIN allowed in the cluster configuration
file. See access policy in cmquerycl(1m).
This command should only be run when the cluster is not active on any of the configured nodes. This command verifies the network configu-
ration before causing the nodes to start their cluster daemons. If a cluster is already running on a subset of the nodes, the cmrunnode
command should be used to start the remaining nodes and force them to join the existing cluster.
If node_name is not specified, the cluster daemons will be started on all the nodes in the cluster. All nodes in the cluster must be
available for the cluster to start unless a subset of nodes is specified.
Options
cmruncl supports the following options:
-f Force cluster startup without warning message and continuation prompt that are printed with the -n option.
-v Verbose output will be displayed.
-t Test only. Provide an assessment of the package placement without affecting the current state of the nodes or packages.
The -w option is not required with the -t option as -t does not validate network connectivity, but assumes that all the
nodes can meet any external dependencies such as EMS resources, package subnets, and storage.
-n node_name...
Start the cluster daemon on the specified subset of node(s).
-w none By default network probing is performed to check that the network connectivity is the same as when the cluster was config-
ured. Any anomalies are reported before the cluster daemons are started. The -w none option disables this probing. The
option should only be used if this network configuration is known to be correct from a recent check.
RETURN VALUE
cmruncl returns the following value:
0 Successful completion.
1 Command failed.
EXAMPLES
Run the cluster daemon:
cmruncl
Run the cluster daemons on node1 and node2:
cmruncl -n node1 -n node2
AUTHOR
cmruncl was developed by HP.
SEE ALSO
cmquerycl(1m), cmhaltcl(1m), cmhaltnode(1m), cmrunnode(1m), cmviewcl(1m), cmeval(1m).
Requires Optional Serviceguard Software cmruncl(1m)