06-22-2011
How about if I do the following will it clean up the stale LUN's
#echo 1 > /sys/block/sdc/device/delete
through
#echo 1 > /sys/block/sdr/device/delete
10 More Discussions You Might Find Interesting
1. Solaris
I have solaris 10 sparc. I installed a Qlogic hba card.
This card is connected on a brocade switch and the brocade is connected on 2 different controllers on a Hitachi disk bay.
I formated 2 luns. On my solaris system, i have 4 disk.
How to configure solaris 10 to fix the dual disk view.
... (4 Replies)
Discussion started by: simquest
4 Replies
2. Solaris
Hi,
I saw your post on the forums about how to setup IP multipathing. I wanted your help on the below situation .
I have 2 servers A and B . Now they should be connected to 2 network switches . S1 and S2.
Now is it possible to have IP Multipathing on each of the servers as follows ?
... (0 Replies)
Discussion started by: maadhuu
0 Replies
3. IP Networking
Hii Every One,
I am working on SUN server installed with Solaris-10,
1) I want to assign a vertual IP to a interface (ce1).
2) And with that vertual IP and one more interface (ce2), I want to do IP
multipathing.
So, kindely help me to achive above tasks by discribing... (2 Replies)
Discussion started by: prashantshukla
2 Replies
4. Solaris
Hi,
Basically the original configuration on my Solaris 9 server was two LUNs configured as Veritas file systems that were connected to a NetApp filer (filer1). These two LUNs are still configured on the server - but are not being used. They are there as a backup just in case the new... (0 Replies)
Discussion started by: sparcman
0 Replies
5. Solaris
Hai
we using emc storage which is conneted to M5000 through san switch.
we asign 13 luns but in server it is showing 22 luns.
i enable the solaris multipathing (MPxIO)
#more /kernel/drv/fp.conf in that file
MPxio-disable=no
#mpathadm list lu
it shows ... (2 Replies)
Discussion started by: joshmani
2 Replies
6. Solaris
Hello,
I turned on the server multipathing:
# uname -a
SunOS caiman 5.10 Generic_141444-09 sun4v sparc SUNW,T5140
stmsboot -D fp -e
And after a reboot the server, multipathing is not enable:
# stmsboot -L
stmsboot: MPxIO is not enabled
stmsboot: MPxIO disabled
# ls /dev/dsk... (4 Replies)
Discussion started by: bieszczaders
4 Replies
7. AIX
Hi,
I know the concept of multipathing, but would like to know how to configure multipathing in AIX.
or software/driver is by default present in AIX??????
How to find out wheather multipathing is configured in AIX?????
Regards,
Manu (4 Replies)
Discussion started by: manoj.solaris
4 Replies
8. Linux
Hi folks.
When issuing a multipath -ll on my server, i see something that is bugging me...
# multipath -ll
2000b0803ce002582 dm-10 Pillar,Axiom 600
size=129G features='0' hwhandler='0' wp=rw
|-+- policy='round-robin 0' prio=50 status=active
| |- 0:0:0:4 sdd 8:48 active ready running... (0 Replies)
Discussion started by: Stephan
0 Replies
9. AIX
What is the following output telling me?
fget_config -Av
---dar0---
User array name = 'BSNorth-DS4300'
dac3 ACTIVE dacNONE ACTIVE
Disk DAC LUN Logical Drive
hdisk4 dac3 0 TestDiskForAll
---dar1---
User array name = 'BSNorth-DS4300'
dac2 ACTIVE dacNONE ACTIVE
Disk DAC ... (0 Replies)
Discussion started by: petervg
0 Replies
10. Red Hat
I have a couple of questions regarding multipath.
If I do vgdisplay vg01, I see it is using 1 PV: /dev/dm-13
If I type multipath -ll I see dm-9, dm-10, dm-11, dm-12, but do not see dm-13. Is my vg01 multipathed? How can I actually know for sure?
Secondly, let's say this time vg01 says... (1 Reply)
Discussion started by: keelba
1 Replies
LEARN ABOUT XFREE86
asadmin-delete-domain
asadmin-delete-domain(1AS) User Commands asadmin-delete-domain(1AS)
NAME
asadmin-delete-domain, delete-domain - deletes the givendomain
SYNOPSIS
delete-domain [--terse=false] [--echo=false] [--domaindir install_dir/domains] domain_name
delete-domain deletes the specified domain. The domain must already exist and must be stopped. This command is supported in local mode
only.
OPTIONS
--domaindir directory where the domain is to be deleted. If specified, path must be accessible in the filesystem. If not speci-
fied, the domain in the default install_dir/domains directory is deleted.
--terse indicates that any output data must be very concise, typically avoiding human-friendly sentences and favoring well-
formatted data for consumption by a script. Default is false.
--echo setting to true will echo the command line statement on the standard output. Default is false.
OPERANDS
domain_name name of the domain. Must be a unique name.
Example 1: Using delete-domain
asadmin> delete-domain sampleDomain
deleted domain sampleDomain successfully
Where: the sampleDomain domain is deleted.
EXIT STATUS
0 command executed successfully
1 error in executing the command
asadmin-create-domain(1AS), asadmin-start-domain(1AS), asadmin-stop-domain(1AS), asadmin-list-domains(1AS)
J2EE 1.4 SDK March 2004 asadmin-delete-domain(1AS)