06-17-2011
I started to tell you what I did to disable it on two of my nodes but that was about 4-5 years ago. I figure things have probably changed a bit since then. So I found this link that will give you some direction.
http://unix.ittoolbox.com/groups/tec...figure-1754493
Hope it helps.
Last edited by juredd1; 06-17-2011 at 10:53 AM..
Reason: Add content
This User Gave Thanks to juredd1 For This Post:
9 More Discussions You Might Find Interesting
1. Solaris
Hello Folks,
I have to restore from remote tape sun solaris 10. It has to have mirror raid.
I have to restore /,/usr, /var,/opt, /etc,/u01.
Could you please give me detailed steps to do the above?
I am new to solaris
Thanks
Ram (1 Reply)
Discussion started by: vr76413
1 Replies
2. IP Networking
As seen on Digg.com, here is my ip addressing article in full...
Original Subnetting in 11 Steps article
Subnetting in 11 Steps
There are a few things that you will need to know first. I personally use 11 rules that I learned from Mike Vana. Below you will find the 11 rules as well as... (1 Reply)
Discussion started by: jking2100
1 Replies
3. HP-UX
Steps to create FileSystem, and later to modify size in HP-UX. Please (1 Reply)
Discussion started by: granador
1 Replies
4. Solaris
Dear All,
I am currently working as Unix Operator. I am looking forward for Unix Solaris Administration.
I need everyone's guidance on this forum, please advice me from where should i start. well i have already installed Solaris version on X86.
So please let me know what should i do to become... (9 Replies)
Discussion started by: imrankhan.in
9 Replies
5. Shell Programming and Scripting
Hello,
I want to start learning Perl, but I need some expert's advice:) Could you recommend me any online manual or book to start with? I have some experience with bash and C, so I am not a complete newbie in programming. What's your advise to start with?
Thank you very much for your answers!
... (5 Replies)
Discussion started by: tsurko
5 Replies
6. UNIX and Linux Applications
Hi All,
Can anybody tell that Where is to find simple and easy steps of ORACLE replication process?
Any help on this highly appreciated.
http://www.unix.com/images/misc/progress.gif Thanks. (1 Reply)
Discussion started by: amit_27
1 Replies
7. AIX
hi,
when I do a failover, hacmp always starts db2 but recently it fails to start db2..noticed the issue is db2nodes.cfg is not modified by hacmp and is still showing primary node..manually changed the node name to secondary after which db2 started immediately..unable to figure out why hacmp is... (4 Replies)
Discussion started by: gkr747
4 Replies
8. AIX
Hi
I'm a little rusty with HACMP, but wanted to find out if it is possible to remove a disk heartbeat network from a running HACMP cluster.
Reason is, I need to migrate all the SAN disk, so the current heartbeat disk will be disappearing. Ideally, I'd like to avoid taking the cluster down to... (2 Replies)
Discussion started by: cmcbugg
2 Replies
9. UNIX for Dummies Questions & Answers
Hi All,
I am working on a new server Dell which I need to install RH version 6.1. I need to document every thing I do on this server, how do I capture screen shot as I do the install?
I used to work on Sun Solaris, I can do this by connecting on COM port after that I had the console access... (2 Replies)
Discussion started by: samnyc
2 Replies
LEARN ABOUT CENTOS
crm_node
PACEMAKER(8) System Administration Utilities PACEMAKER(8)
NAME
Pacemaker - Part of the Pacemaker cluster resource manager
SYNOPSIS
crm_node command [options]
DESCRIPTION
crm_node - Tool for displaying low-level node information
OPTIONS
-?, --help
This text
-$, --version
Version information
-V, --verbose
Increase debug output
-Q, --quiet
Essential output only
Stack:
-A, --openais
Only try connecting to an OpenAIS-based cluster
-H, --heartbeat
Only try connecting to a Heartbeat-based cluster
Commands:
-n, --name
Display the name used by the cluster for this node
-N, --name-for-id=value
Display the name used by the cluster for the node with the specified id
-e, --epoch
Display the epoch during which this node joined the cluster
-q, --quorum
Display a 1 if our partition has quorum, 0 if not
-l, --list
Display all known members (past and present) of this cluster (Not available for heartbeat clusters)
-p, --partition
Display the members of this partition
-i, --cluster-id
Display this node's cluster id
-R, --remove=value
(Advanced) Remove the (stopped) node with the specified name from Pacemaker's configuration and caches
In the case of Heartbeat, CMAN and Corosync 2.0, requires that the node has already been removed from the underlying cluster
Additional Options:
-f, --force
AUTHOR
Written by Andrew Beekhof
REPORTING BUGS
Report bugs to pacemaker@oss.clusterlabs.org
Pacemaker 1.1.10-29.el7 June 2014 PACEMAKER(8)