Here's a conundrum. I use a ThinkPad (T30) which has a slot on the side for the hard drive. It is very easy to swap this with another hard drive which I keep as a backup. Now when I copy the Linux partition from my (in use) hard drive to the backup one (in my UltraBay slot) it takes only 30 minutes. If instead I copy this partition to my storage drive (in my docking station's drive slot) and save it as a file, the same copying takes 2 and a half hours. How come so much longer? Any thoughts?
From the hard drive to the backup I use this:
From the hard drive to a storage drive I use:
Note that the file size is 18.0GB and the partition size is 28.6GB.
Last edited by pludi; 06-13-2011 at 09:32 AM..
Reason: Additional information added.
hi,
1) is logical partition the same as physical partition except that one is physical and the other is logical?
2) then it must a one to one ratio? (3 Replies)
I presently backup my multi-OS multi-paritition boot drive (fedora core 4/ext3, WinXPServer/NTFS, WinXPHome/FAT32) with the command:
telinit 1; cp /dev/sda /dev/sdb
And this works.
Is there a command to only copy a single partition instead of an entire device?
And what about the grub... (12 Replies)
I've created a partition with GNU Parted, how do I mount the partition?
The manual information at http://www.gnu.org/software/parted/manual/parted.html is good, but I am sure about how I mount the partition afterwards.
Thanks,
--Todd (1 Reply)
Scenario:
I would want to copy my / to /mnt, and to avoid recursion exclude /mnt.
cp -avx / /mnt
If i use the above i believe it would run recursively, and end up in mess. So how to do it ?!
Basically this / is sda1, and /mnt is sda2 and sda1 is where only OS is available & currently... (2 Replies)
I have found a question from the exercises of my study mat. The question is
"Why are there a in-core copy and a disk-copy of i-node block and super block?"
If any one know the proper answer then please send me..... (1 Reply)
This is now a larger script than I would customarily post. But many folks have become accustom to getting it off this forum.
Every couple of years I update my favorite scripts. This script is one that I use regularly and have posted older versions every couple of years. I noticed that it has... (3 Replies)
Gentleman,
Please move if I have chose the incorrect forum section. I am trying to move data that is not backed up from partition 1 to partition 2 on a SAN that has a GFS2 filesystem. Since the data is not backed up I am rsyncing this data and once verified I will delete from the source... (6 Replies)
hi all
while formatting hard disk i am getting following error.
Partition 1 ends at 266338338
It must be between 34 and 143374704.
label error: EFI Labels do not support overlapping partitions
Partition 8 overlaps partition 1.
Warning: error writing EFI.
Label failed.
I have formatted the... (2 Replies)
Hi Experts
I would like to know different between soft partition concept and hard partition concept on solaris.
Here is little explanation between soft partition concept and hard partition concept on solaris.
Soft Partition:
1TB total space available in storage in all mapped to the OS to... (2 Replies)
Hello All,
I have a Red Hat Linux 5.9 Server installed with one hard disk & 2 Partitions created on it as follows,
/boot - Linux Partition & another is
LVM - One VG & under that 5-6 Logical volumes(var,opt,home etc).
Here my requirement is to take out 1GB of space from LVM ( Any logical... (5 Replies)
Discussion started by: gr8_usk
5 Replies
LEARN ABOUT OSF1
disklabel
disklabel(4) Kernel Interfaces Manual disklabel(4)NAME
disklabel - Disk pack label
SYNOPSIS
#include <sys/disklabel.h>
DESCRIPTION
Each disk or disk pack on a system may contain a disk label which provides detailed information about the geometry of the disk and the par-
titions into which the disk is divided. It should be initialized when the disk is formatted, and may be changed later with the disklabel
program. This information is used by the system disk driver and by the bootstrap program to determine how to program the drive and where
to find the file systems on the disk partitions. Additional information is used by the file system in order to use the disk most effi-
ciently and to locate important file system information. The description of each partition contains an identifier for the partition type
(standard file system, swap area, etc.). The file system updates the in-core copy of the label if it contains incomplete information about
the file system.
The label is located in sector number LABELSECTOR of the drive, usually sector 0 (zero) where it may be found without any information about
the disk geometry. It is at an offset LABELOFFSET from the beginning of the sector, to allow room for the initial bootstrap. The disk
sector containing the label is normally made read-only so that it is not accidentally overwritten by pack-to-pack copies or swap opera-
tions; the DIOCWLABEL ioctl, which is done as needed by the disklabel program, allows modification of the label sector.
A copy of the in-core label for a disk can be obtained with the DIOCGDINFO ioctl; this works with a file descriptor for a block or charac-
ter (raw) device for any partition of the disk. The in-core copy of the label is set by the DIOCSDINFO ioctl. The offset of a partition
cannot generally be changed, nor made smaller while it is open. One exception is that any change is allowed if no label was found on the
disk, and the driver was able to construct only a skeletal label without partition information. Finally, the DIOCWDINFO ioctl operation
sets the in-core label and then updates the on-disk label; there must be an existing label on the disk for this operation to succeed.
Thus, the initial label for a disk or disk pack must be installed by writing to the raw disk. All of these operations are normally done
using the disklabel program.
RELATED INFORMATION
Files: disktab(4)
Commands: disklabel(8) delim off
disklabel(4)