Here's a conundrum. I use a ThinkPad (T30) which has a slot on the side for the hard drive. It is very easy to swap this with another hard drive which I keep as a backup. Now when I copy the Linux partition from my (in use) hard drive to the backup one (in my UltraBay slot) it takes only 30 minutes. If instead I copy this partition to my storage drive (in my docking station's drive slot) and save it as a file, the same copying takes 2 and a half hours. How come so much longer? Any thoughts?
From the hard drive to the backup I use this:
From the hard drive to a storage drive I use:
Note that the file size is 18.0GB and the partition size is 28.6GB.
Last edited by pludi; 06-13-2011 at 09:32 AM..
Reason: Additional information added.
hi,
1) is logical partition the same as physical partition except that one is physical and the other is logical?
2) then it must a one to one ratio? (3 Replies)
I presently backup my multi-OS multi-paritition boot drive (fedora core 4/ext3, WinXPServer/NTFS, WinXPHome/FAT32) with the command:
telinit 1; cp /dev/sda /dev/sdb
And this works.
Is there a command to only copy a single partition instead of an entire device?
And what about the grub... (12 Replies)
I've created a partition with GNU Parted, how do I mount the partition?
The manual information at http://www.gnu.org/software/parted/manual/parted.html is good, but I am sure about how I mount the partition afterwards.
Thanks,
--Todd (1 Reply)
Scenario:
I would want to copy my / to /mnt, and to avoid recursion exclude /mnt.
cp -avx / /mnt
If i use the above i believe it would run recursively, and end up in mess. So how to do it ?!
Basically this / is sda1, and /mnt is sda2 and sda1 is where only OS is available & currently... (2 Replies)
I have found a question from the exercises of my study mat. The question is
"Why are there a in-core copy and a disk-copy of i-node block and super block?"
If any one know the proper answer then please send me..... (1 Reply)
This is now a larger script than I would customarily post. But many folks have become accustom to getting it off this forum.
Every couple of years I update my favorite scripts. This script is one that I use regularly and have posted older versions every couple of years. I noticed that it has... (3 Replies)
Gentleman,
Please move if I have chose the incorrect forum section. I am trying to move data that is not backed up from partition 1 to partition 2 on a SAN that has a GFS2 filesystem. Since the data is not backed up I am rsyncing this data and once verified I will delete from the source... (6 Replies)
hi all
while formatting hard disk i am getting following error.
Partition 1 ends at 266338338
It must be between 34 and 143374704.
label error: EFI Labels do not support overlapping partitions
Partition 8 overlaps partition 1.
Warning: error writing EFI.
Label failed.
I have formatted the... (2 Replies)
Hi Experts
I would like to know different between soft partition concept and hard partition concept on solaris.
Here is little explanation between soft partition concept and hard partition concept on solaris.
Soft Partition:
1TB total space available in storage in all mapped to the OS to... (2 Replies)
Hello All,
I have a Red Hat Linux 5.9 Server installed with one hard disk & 2 Partitions created on it as follows,
/boot - Linux Partition & another is
LVM - One VG & under that 5-6 Logical volumes(var,opt,home etc).
Here my requirement is to take out 1GB of space from LVM ( Any logical... (5 Replies)
Discussion started by: gr8_usk
5 Replies
LEARN ABOUT SUNOS
volcheck
volcheck(1) User Commands volcheck(1)NAME
volcheck - checks for media in a drive and by default checks all floppy media
SYNOPSIS
volcheck [-v] [-i secs] [-t secs] pathname
DESCRIPTION
The volcheck utility tells Volume Management to look at each dev/pathname in sequence and determine if new media has been inserted in the
drive.
The default action is to volcheck all checkable media managed by volume management.
OPTIONS
The following options are supported:
-i secs Set the frequency of device checking to secs seconds. The default is 2 seconds. The minimum frequency is 1 second.
-t secs Check the named device(s) for the next secs seconds. The maximum number of seconds allowed is 28800, which is 8 hours. The fre-
quency of checking is specified by -i. There is no default total time.
-v Verbose.
OPERANDS
The following operands are supported:
pathname The path name of a media device.
EXAMPLES
Example 1: A sample of the volcheck command.
The following example
example% volcheck -v /dev/diskette
/dev/diskette has media
asks Volume Management to examine the floppy drive for new media.
The following example
example% volcheck -i 2 -t 600 /dev/diskette1 &
asks Volume Management if there is a floppy in the floppy drive every 2 seconds for 600 seconds (10 minutes).
FILES
/dev/volctl Volume Management control port
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWvolu |
+-----------------------------+-----------------------------+
SEE ALSO eject(1), volcancel(1), volmissing(1)rmmount(1M), vold(1M), rmmount.conf(4), vold.conf(4), attributes(5), volfs(7FS)WARNINGS
Due to a hardware limitation in many floppy drives, the act of checking for media causes mechanical action in the floppy drive. Continu-
ous polling of the floppy drive will cause the drive to wear out. It is recommended that polling the drive only be performed during periods
of high use.
SunOS 5.10 21 Feb 1997 volcheck(1)