Hello,
I have a single column of data that I would like to cut/print (with awk or ...) into multiple columns at every empty row (or common character).
Input:
5.99123
5.94693
7.21383
5.95202
0.907935
5.99149
6.08427
0.975774
6.077
Output:
5.99123 5.95202 6.08427
5.94693... (7 Replies)
Hi -
I'm new to the awk programming language. I'm trying to print a single column of data to several columns, and I found an article on iTWorld.com (ITworld.com - Printing in columns). It looks like the mkCols2 script is very close to what I need to do, but it looks like the end of the code... (2 Replies)
I have a program which gives me the output as a single column with hundreds of rows like:
213
314
324
324
123
I want to be able to create a new file from this file which allows me to set the number of rows and columns in the new file, i.e. for this example, if I specify 3 rows and 2... (5 Replies)
Apologies if this has been covered - I did search but couldn't find what I was looking for.
I have a simple X-Y input file. I want to convert it from two columns into 8 columns - 4 pairs of X-Y data. So my input file looks like
X1 Y1
X2 Y2
X3 Y3
X4 Y4
X5 Y5
etc
And I want it to look... (8 Replies)
Hello Experts,
I am new to this forum, I would like to do the following changes in one of the column of a txt file, which is having around 9 column.
For example, column 3 is having letters like this
AB11
AB12
C
CA
CB
AC1
AC2
I would like to convert the same column as follows
... (5 Replies)
Hello all
I have data like
1
2
3
4
5
I wish my output would be like
1,2,3,4,5
For this i have executed
'BEGIN {FS="\n"; ORS=","} {print $0}' test
and got the output as
1,2,3,4,5,
I do not want to have , at the end of 5. output should be like (5 Replies)
I have this input:
10 22 1 100
11 22 10 1 50
14 3 1 100
23 3 1 100
24 15 1 100
10 22 5 3 1 33.333
11 22 1 100
It has an inconsistent number of fields but the last field is determined by 100/(NF-2) using awk.
I want to take this multiple columned input file and transform so that... (2 Replies)
Dear All,
We have input like this:
161 57 1378 176 1392 262 1444 441 1548 538 1611 670 1684
241 57 1378 208 1393 269 1447 444 1549 538 1610 677 1700
321 ... (4 Replies)
Discussion started by: attila
4 Replies
LEARN ABOUT SUNOS
bestups
BESTUPS(8) NUT Manual BESTUPS(8)NAME
bestups - Driver for Best Power / SOLA (Phoenixtec protocol) UPS equipment
NOTE
This man page only documents the hardware-specific features of the bestups driver. For information about the core driver, see nutupsdrv(8).
SUPPORTED HARDWARE
bestups was designed to monitor Best Power UPS hardware like the Fortress, Fortress Telecom, Axxium Rackmount and Patriot Pro. It also
recognizes and supports SOLA units such as the 325, 520 and 620. In addition, the Best 610 is supported using the 'ID' option.
Other UPS hardware using the Phoenixtec protocol should also work, but they will generate a warning since their battery information is not
known.
This driver does not support some older Best/SOLA units.
EXTRA ARGUMENTS
This driver supports the following optional settings in the ups.conf(5):
nombattvolt=num
Override the battery float voltage which is normally determined by asking the hardware. This is useful if your UPS constantly reports
battery.charge values just below 100% even when it's completely charged.
If you have this problem, set this to whatever battery.voltage reports when the UPS is known to be completely charged with a good
battery.
The author's Best Fortress 750 uses nombattvolt=27.4.
battvoltmult=num
Multiply the reported battery voltage by this number. Some devices report only a fraction of the total battery voltage.
For example, the SOLA 610 700VA UPS (with a 24V battery) reports the single cell voltage (about 2.27V when fully charged). In this
particular case you can set battvoltmult = 12 in ups.conf(8) to fix this.
ID=string
Set the Identification response string. This should only be used with hardware that supports the Phoenixtec protocol status inquiry
commands, but not the "ID" command, such as the Best/SOLA 610. Format of the ID string is: AAA,BBBB,CCC,DDD,EE.E,FF.F
AAA is the three-character identification for the UPS model.
BBBB is the output power in VA (volt amperes). B is an integer number ranging from 0 to 9.
CCC is the Nominal Input Voltage. C is an integer number ranging from 0 to 9. The unit is Volts AC.
DDD is the Nominal Output Voltage. D is an integer number ranging from 0 to 9. The unit is Volts AC.
EE.E is the Battery Voltage that will cause the UPS to shut itself off. E is an integer number ranging from 0 to 9. Then unit is Volts
DC and a decimal point is present.
FF.F or FFF.F is the Battery Voltage at full charge. F is an integer number ranging from 0 to 9. Then unit is Volts DC. Typically, for
700VA, 1KVA and 1.5KVA units, the format is FF.F. For 2KVA and 3KVA units, the format is FFF.F.
Example: a Best 610 1.5KVA unit would use the string "610,1500,120,120,10.0,48.0".
BUGS
The battery charge percentage value (in battery.charge) is derived from the voltage data that the UPS returns, since the UPS doesn't return
that value directly. On some hardware, the charge will remain at 100% for a long time and then drops quickly shortly before the battery
runs out. You can confirm from the battery.voltage readings that this is a problem with the UPS and not this driver.
Similarly, the float from the charger in some models forces the battery charge percentage back up to 100% immedately after the UPS goes
back on-line, so you can't tell when it is really recharged.
Finally, some models give one value for the battery's nominal voltage and yet actually have a nominal voltage slightly below that. This
leads to things such as the perpetual 98.7% charge on the author's Fortress 750, even when it's been charging for weeks. You can use
nombattvolt= in ups.conf(8) to fix this.
AUTHOR
Russell Kroll, Jason White
SEE ALSO
The core driver:
nutupsdrv(8)
Internet resources:
The NUT (Network UPS Tools) home page: http://www.networkupstools.org/
Network UPS Tools 05/21/2012 BESTUPS(8)