06-01-2011
What I would like to know is:
1.) If I create the RAID volumes from the OBP, how would the OS know when a disk has failed?
2.) In the event of a disk failure, do I have to bring the server down to the OBP to replace the disk OR is it a case of swapping the drives and OBP is clever enough to update itself with the new device path etc?
---------- Post updated at 03:05 PM ---------- Previous update was at 12:13 PM ----------
Things just got even more interesting. It seems I'm limited to 2 volumes if I configure RAID from OBP. What's that about?
The server can take 16 disks and I'm limited to only 2 RAID 1 volumes, surely that can't be right?
9 More Discussions You Might Find Interesting
1. Solaris
I don't understood why on SPARC-Platforms have not present RAID-Controller ? Sorry for my bad english, but it's crazy always setup software RAID !!! I whanna Hardware RAID and when i can find solution ? (7 Replies)
Discussion started by: jess_t03
7 Replies
2. Solaris
Hi,
I have t5120 sparc and I have 2 146 G drives in the system. I will be installing solaris 10 and also want the system mirrored using Hardware RAID "1"
The System did come preinstalled as it comes from sun. I did not do much on it.
I booted system using boot cdrom -s
gave format... (6 Replies)
Discussion started by: upengan78
6 Replies
3. Solaris
Hi everyone
I've just purchased a Sun T5120 server with 2 internal disks. I've configured hardware RAID (mirror) and as a result the device tree in Solaris only contains 1 hard drive.
My question is, how would I know when one of the drives become faulty?
Thanks (2 Replies)
Discussion started by: soliberus
2 Replies
4. UNIX for Dummies Questions & Answers
Hi
Can someone tell me what are the differences between software and hardware raid ?
thx for help. (2 Replies)
Discussion started by: presul
2 Replies
5. Solaris
Hi,
I have a question. Do LiveUpgrade supports hardware raid?
How to choose the configuration of the system disk for Solaris 10 SPARC?
1st Hardware RAID-1 and UFS
2nd Hardware RAID-1 and ZFS
3rd SVM - UFS and RAID1
4th Software RAID-1 and ZFS
I care about this in the future to take... (1 Reply)
Discussion started by: bieszczaders
1 Replies
6. Hardware
Hi All
I have a Sun T2000 server. Couple of years ago I had configured and mirrored the boot drive with an other drive using hardware RAID 1 using raidctl command.
Following is the hardware RAID output.
root@oracledatabaseserver / $ raidctl
RAID Volume RAID RAID Disk... (0 Replies)
Discussion started by: Tirmazi
0 Replies
7. Solaris
Server Model: T5120 with 146G x4 disks.
OS: Solaris 10 - installed on c1t0d0.
Plan to use software raid (veritas volume mgr) on c1t2d0 disk.
After format and label the disk, still not able to detect using vxdiskadm.
Question:
Should I remove the hardware raid on c1t2d0 first?
My... (4 Replies)
Discussion started by: KhawHL
4 Replies
8. Solaris
We have hardware RAID configured on Sun-Blade-T6320 and one of the disk got failed. Hence we replaced the failed disk. But the hot swapped disk not recognized by RAID. Kindly help on fixing this issue.
We have 2 LDOM configured on this server and this server running on single disk.
#... (8 Replies)
Discussion started by: rock123
8 Replies
9. Solaris
Dear All ,
we have hardware raid 1 implemented on Solaris Disks.
We need to patch the Servers. Kindly let me know how to patch hardware raid implemented Servers.
Thanks...
Rj (7 Replies)
Discussion started by: jegaraman
7 Replies
LEARN ABOUT REDHAT
raidstop
raidstart(8) System Manager's Manual raidstart(8)
NAME
raidstart, raidstop, - command set to manage md devices.
SYNOPSIS
raidstart [options] <raiddevice>*
raidstop [options] <raiddevice>*
DESCRIPTION
RAID devices are virtual devices created from two or more real block devices. This allows multiple disks to be combined into a single
filesystem, possibly with automated backup and recovery. Linux RAID devices are implemented through the md device driver.
If you're using the /proc filesystem, /proc/mdstat gives you informations about md devices status.
Currently, Linux supports linear md devices, RAID0 (striping), RAID1 (mirrroring), and RAID4 and RAID5. For information on the various lev-
els of RAID, check out:
http://ostenfeld.dk/~jakob/Software-RAID.HOWTO/
for new releases of the RAID driver check out:
ftp://ftp.fi.kernel.org/pub/linux/daemons/raid/alpha
Avaible commands are :
mkraid : configures (creates) md (RAID) devices in the kernel, banding multiple devices into one.
raidstart : activates (starts) an existing 'persistent' md device
raid0run : activates old nonpersistent RAID0/LINEAR md devices
raidstop : turns off an md device, and unconfigures (stops) it
By default, a systems RAID configuration is kept in /etc/raidtab, which can configure multiple RAID devices.
All of these tools work similiarly. If -a (or --all) is specified, the specified operation is performed on all of the RAID devices men-
tioned in the configuration file. Otherwise, one or more RAID devices must be specified on the command line. For example:
raid0run -a
Starts all of the 'old' RAID0 RAID devices specified in /etc/raidtab. If only /dev/md1 should be started, the following command should be
used instead:
raidstart /dev/md1
OPTIONS
-a, --all
Apply the command to all of the configurations specified in the config file.
-c, --configfile filename
Use filename as the configuration file (/etc/raidtab is used by default).
-h, --help
Displays a short usage message, then exits.
-V, --version
Displays a short version message, then exits.
NOTES
The raidtools are derived from the md-tools and raidtools packages, which were originally written by Marc Zyngier, Miguel de Icaza, Gadi
Oxman, Bradley Ward Allen, and Ingo Molnar.
BUGS
no known bugs.
SEE ALSO
raidtab(5), raid0run(8), raidstop(8), mkraid(8)
raidstart(8)