05-28-2011
There is no "linux 10.04", presumably 10.04 is a revision of some distribution or other.
If it can't find sda5, that means it's either not finding your disk because you didn't compile in the right disk controller drivers, or the device's name changed from sda to hda.
10 More Discussions You Might Find Interesting
1. Solaris
Hi,
I've just bought an Ultra 60 running solaris 9 (or so I've been led to believe). When I start up, it looks for a (presumably) domain/network to hook up to and the following messages are displayed:
Boot device: net file and args:
Network link setup failed
Please check cable and try... (3 Replies)
Discussion started by: alarmcall
3 Replies
2. AIX
Hi all ,
i was trying to upgrade firmware on machine 7028-6E4 and it failed .
Now machine does not boot anymore , i can not get SMC menu either ...
What are my options ?
Thanks,
Rahim (1 Reply)
Discussion started by: rahim
1 Replies
3. Solaris
I'm running solaris 2.5.1. My main development server is DEAD, i can't even boot off the cdrom, it powers up, acts like it is starting the boot process but then says cannot find boot device. I've done the search here on this site and saw the other posts, but at the ok prompt it won't even let me... (3 Replies)
Discussion started by: kymberm
3 Replies
4. Solaris
Solaris system
version 6
I cloned the drive using the DD command.
Using the format command and examining the partitions, all looks the same as the original drive.
Problem:
When I attach the cloned drive as the master, and only drive in system, it will not boot.
Error messages:
... (9 Replies)
Discussion started by: HikerLT
9 Replies
5. Solaris
I just was given an Ultra 60 that I'm trying to get started so that I can re-load the system with Solaris 10. I can't seem to get the system to boot past the initial memory check. I've tried to do an Stop-A to get to the eeprom, but can't do that. My next step is to try to send a break from the... (0 Replies)
Discussion started by: zosojohnny
0 Replies
6. UNIX for Dummies Questions & Answers
I'm trying to install Fedora 9 on a Dell OptiPlex GX300 machine. The instalation runs properly, but when the computer restarts after the instalation, it simply won't boot, like there's no OS installed.
I tried diffrent Linux distributions, but nothing works.
This are the partitions, maybe it's... (12 Replies)
Discussion started by: teis
12 Replies
7. AIX
Hello:
NOOB here. I attempted to use smit mkcd. Failed on first attempt, not enough space. 2nd attempt tried to place iso on /usr, not enough space there. Cleanup ran for about 5 minutes after aborting. Now AIX won't boot. LCD display on 7029-6E3 says: 0517 MOUNT /USR. Attempted to boot from CD... (11 Replies)
Discussion started by: bbird
11 Replies
8. UNIX for Dummies Questions & Answers
First of all, I'd like to preface this post by relaying that I have considerable experience with FreeBSD but I'm a Linux newb. I've been attempting to compile linux-2.6.29.3 from source and I'm having some problems and have a few newb questions...
a) First of all, my kernel won't boot, it fails... (0 Replies)
Discussion started by: urbanriot
0 Replies
9. SCO
Our system is not booting up properly. It keeps going to this screen:
Enter Run Level (0-6, s or S):
I tried to hit all nos# 0-6 is just goes to hung state.
Tried s or S & it brings me to single user mode. I've checked the file systems & found out that all three had 98%. I tried to... (86 Replies)
Discussion started by: jedimaster
86 Replies
10. Linux
Hi everyone,
I am trying to prevent the ehci_hcd kernel module to load at boot time.
Here's what I've tried so far:
1) Add the following line to /etc/modprobe.d/blacklist.conf (as suggested here):
2) Blacklisted the module by adding the following string to
3) Tried to blacklist the module... (0 Replies)
Discussion started by: gacanepa
0 Replies
LEARN ABOUT X11R4
mkfs.minix
MKFS.MINIX(8) System Administration MKFS.MINIX(8)
NAME
mkfs.minix - make a Minix filesystem
SYNOPSIS
mkfs.minix [options] device [size-in-blocks]
DESCRIPTION
mkfs.minix creates a Linux MINIX filesystem on a device (usually a disk partition).
The device is usually of the following form:
/dev/hda[1-8] (IDE disk 1)
/dev/hdb[1-8] (IDE disk 2)
/dev/sda[1-8] (SCSI disk 1)
/dev/sdb[1-8] (SCSI disk 2)
The device may be a block device or a image file of one, but this is not enforced. Expect not much fun on a character device :-).
The size-in-blocks parameter is the desired size of the file system, in blocks. It is present only for backwards compatibility. If omit-
ted the size will be determined automatically. Only block counts strictly greater than 10 and strictly less than 65536 are allowed.
OPTIONS
-c, --check
Check the device for bad blocks before creating the filesystem. If any are found, the count is printed.
-n, --namelength length
Specify the maximum length of filenames. Currently, the only allowable values are 14 and 30 for file system versions 1 and 2. Ver-
sion 3 allows only value 60. The default is 30.
-i, --inodes number
Specify the number of inodes for the filesystem.
-l, --badblocks filename
Read the list of bad blocks from filename. The file has one bad-block number per line. The count of bad blocks read is printed.
-1 Make a Minix version 1 filesystem. This is the default.
-2, -v Make a Minix version 2 filesystem.
-3 Make a Minix version 3 filesystem.
-V, --version
Display version information and exit. The long option cannot be combined with other options.
-h, --help
Display help text and exit.
EXIT CODES
The exit code returned by mkfs.minix is one of the following:
0 No errors
8 Operational error
16 Usage or syntax error
SEE ALSO
fsck(8), mkfs(8), reboot(8)
AVAILABILITY
The mkfs.minix command is part of the util-linux package and is available from https://www.kernel.org/pub/linux/utils/util-linux/.
util-linux June 2015 MKFS.MINIX(8)