05-23-2011
You've used the -a option for tee which appends instead of overwrites the file
10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
Hi:
I am currently working on a program which requires direct its ouput to a file here is an example
./proram arg_1 arg_2
when program ends all output will be arg_2 file
Is that possible I am not a bad programmer, However I am stuck there.
Can anyone give a hint?
Thanks
SW (1 Reply)
Discussion started by: slackware
1 Replies
2. UNIX for Dummies Questions & Answers
Ahhhrrrggg I'm having a brain fart...
I want to take the output of a command and redirect it to a file...
This works....
$ man cp | cat >> copy_help
but this doesn't
keytool -help |cat >> keytool_help
It just produces... these lines...
more keytool_help
] ...
... (11 Replies)
Discussion started by: jimmyc
11 Replies
3. UNIX for Dummies Questions & Answers
Hi all!!
is possible to assign the output of some command to filename, i.e.
grep_output.txt
Otherwise, I want to open a new file which name is inside another, how can I do it?
Thanks a lot! (7 Replies)
Discussion started by: csecnarf
7 Replies
4. Shell Programming and Scripting
Hi guys,
i have a script named purgeErrors.ksh, when i execute this script i need to redirect the output to a log file in the same directory, how can i do that ??
-- Aditya (5 Replies)
Discussion started by: chaditya
5 Replies
5. Shell Programming and Scripting
Hi All,
I want to redirect only the file names to a new file from the ls -ltr directroy. how Can i do it.
my ls -ltr output will be as below.
-rwxr-xr-x 1 118 103 28295 Jul 26 2006 event.podl
-rwxr-xr-x 1 118 103 28295 Jul 26 2006 xyz.podl
I want my new file... (6 Replies)
Discussion started by: girish.raos
6 Replies
6. Shell Programming and Scripting
Dear all,
redirecting STDOUT & STDERR to file is quite simple, I'm currently using:
exec 1>>/tmp/tmp.log; exec 2>>/tmp/tmp.logBut during script execution I would like the output come back again to screen, how to do that?
Thanks
Lucas (4 Replies)
Discussion started by: Lord Spectre
4 Replies
7. Shell Programming and Scripting
Below script perfectly works, giving below mail output. BUT, I want to make the script mail only if there are any D-Defined/T-Transition/B-Broken State WPARs and also to copy the output generated during monitoring to a temporary log file, which gets cleaned up every week. Need suggestions.
... (4 Replies)
Discussion started by: aix_admin_007
4 Replies
8. Shell Programming and Scripting
Hi Guys,
I want to redirect the output of 3 scripts to a file and then mail the output of those three scripts.
I used below but it is not working:
OFILE=/home/home1/report1
echo "report1 details" > $OFILE
=/home/home1/1.sh > $OFILE
echo... (7 Replies)
Discussion started by: Vivekit82
7 Replies
9. Shell Programming and Scripting
Dear all,
redirecting STDOUT & STDERR to file is quite simple, I'm currently using:
Code:
exec 1>>/tmp/tmp.log; exec 2>>/tmp/tmp.log
But during script execution I would like the output come back again to screen, how to do that?
Thanks
Luc
edit by bakunin: please use CODE-tags like the... (6 Replies)
Discussion started by: tmonk1
6 Replies
10. UNIX for Beginners Questions & Answers
Hi All,
I am trying to out of shell script when i run it
like
sh /mypath/abc.sh
....a screen log should be generated whenever i input the values, when above the script prompt for values
Regards
Amarendra (3 Replies)
Discussion started by: amar1208
3 Replies
tee(1) General Commands Manual tee(1)
NAME
tee - Displays the output of a program and copies it into a file
SYNOPSIS
tee [-ai] file...
STANDARDS
Interfaces documented on this reference page conform to industry standards as follows:
tee: XCU5.0
Refer to the standards(5) reference page for more information about industry standards and associated tags.
OPTIONS
Adds the output to the end of file instead of writing over it. Ignores the SIGINT signal.
OPERANDS
Standard input is stored into, or appended to, the file specified.
[Tru64 UNIX] The tee command can accept up to 20 file arguments.
DESCRIPTION
The tee command reads standard input and writes to both standard output, and each specified file.
The tee command is useful when you wish to view program output as it is displayed, and also want to save it in a file. The tee command does
not buffer output, so you may wish to pipe the output of tee to more if more than one full screen of data is anticipated.
NOTES
If a write to any file fails, the exit status of tee will be non-zero. Writes to all other specified files may be successful, and opera-
tion will continue until standard input is exhausted.
EXIT STATUS
The following exit values are returned: Successful completion. An error occurred.
EXAMPLES
To view and save the output from a command at the same time, enter: lint program.c | tee program.lint
This displays the standard output of the command lint program.c at the terminal, and at the same time saves a copy of it in the file
program.lint. If program.lint already exists, it is deleted and replaced. To display and append to a file, enter: lint program.c |
tee -a program.lint
This displays the standard output of lint program.c at the terminal and at the same time appends a copy of it to the end of pro-
gram.lint. If the file program.lint does not exist, it is created.
ENVIRONMENT VARIABLES
The following environment variables affect the execution of tee: Provides a default value for the internationalization variables that are
unset or null. If LANG is unset or null, the corresponding value from the default locale is used. If any of the internationalization vari-
ables contain an invalid setting, the utility behaves as if none of the variables had been defined. If set to a non-empty string value,
overrides the values of all the other internationalization variables. Determines the locale for the interpretation of sequences of bytes
of text data as characters (for example, single-byte as opposed to multibyte characters in arguments). Determines the locale for the for-
mat and contents of diagnostic messages written to standard error. Determines the location of message catalogues for the processing of
LC_MESSAGES.
SEE ALSO
Commands: cat(1), echo(1), script(1)
Standards: standards(5)
tee(1)